Maytag HE21250PC, HE21282PC operating instructions Programming the Thermostat contd

Instructions for Operation (cont'd)

Programming the Thermostat (cont'd)

The third optional mode (3) setting involves the default tern- perature set point for the control. To be in this mode, depress

the up ( • ) arrow or the down (•) arrow until a large number 3 appears in the lower right-hand corner. The default temperature

from the factory is 120°F. This will appear in the upper-left

hand corner as 0120. To change the default setting, depress

either - of the "TIME" button until the desired default temperature is displayed in the upper left-hand comer. The

range for set point temperature is 80°F to 160°E

----	_._
	_ i
	]
MAYFAG	= = !

The fourth optional mode (4) setting involves the vacation tem-

perature setting. This is factory set at 800F or 0080 in the upper left-handcorner. To change the vacation default setting, make

sure the optional mode is in the number (4) setting by depress-

ing the up (•) arrowor the down ( • ) arrow button until a

large number 4 is displayed in the lower right-hand corner. To change the vacation temperature default setting, depress either + or - of the "TIME" button until the desired vacation tempera- ture is achieved in the upper left-hand comer of the display.

The range for vacation default setting is 60°F to 1200E

..

- ....

=_

"

k'_ MAYI'AG eJ_

The fifth optional mode (5) setting involves the maximum tern- perature set point. To he this mode, depress the up (_,) arrow

or the down (•) arrow while in optional setting sequence until

a large number 5 is displayed in the lower right-hand corner. The default factory maximum set point is 1600F or 0160 in the

upper left-hand comer. To change this setting depress either +

or - of the "TIME" button until the desired maximum set point

is achieved in the upper left-hand comer. The range for maxi- mum set point is 100°F to 160°E

_-	--	=-
		i	]
		_	[
		_
		_	; [
k'_ MAYrAG		_	[
			,,,

To return to regular operation of the program control, depress the "PROGRAM" and "MODE" butt ons sire ultan eously again until the normal display appears. All the optional settings that were revised will remain until they are once again reset by

using the above prescribed procedures.

SCALD WARNING is a flashing displaywarning any time

the temperature is adjusted above 120°E It represents an indus- try warning that water ternperatuses above 120°F represent a scald hazard when skin surface is exposed for a small amount of time. This is a warning and can not be removed from the screen

display.

"PWR" fPOWER) BUTTON is a button at the right-hand bottom of the panel which will activate or deactivate the display panel. It will not turn offthe power to the water heater and will not kill the uower to the heatin_ elements.

--

AWARNING

HAZARD OF ELECTRICAL SHOCK! Before removinc

any access panels or servicing the water heater make sure the electrical supply to the water heate=

is turned "OFF". Failure to do this could result in

DEATH, SER OUS BOD LY NJURY, OR PROPERTY DAMAGE.

ELECTRICAL POWER OUTAGES will not effect the

Intelligent programming or control settings. The unit has a bat- tery backup that maintains the programmed settings until the electrical power is restored. At the time power is restored the program _ again display the settings and information that had been available before the loss of power.

DRY FIRE PREVENTION is a feature that has been pro- grammed into the lntelllgent water heater. Should someone install or service the water heater and forget to ill/the tank, the unit will sense a rapid heat cycle beyond normal expectations and disable the energy. A message will be displayed on the screen to add water, at which time the unit can be re-energized.

26