Dryer Dimensions
43½"
(110.5 cm)
| 22¼" |
*29¼" | (56.5 cm) |
(74.3 cm) | 29" |
| |
| (73.7 cm) |
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the exhaust vent with elbow. See “Venting Requirements.”
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:
■Additional spacing should be considered for ease of installation and servicing.
■Additional clearances might be required for wall, door and floor moldings.
■Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
■For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
■Companion appliance spacing should also be considered.
■Additional spacing is required if you exhaust out the rear of the dryer to either the right or left side.
Mobile home - Additional installation requirements
This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard
Mobile home installations require:
■Metal exhaust system hardware, which is available for purchase from your dealer.
■Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.
Electrical Requirements - U.S.A. Only
It is your responsibility
■ To contact a qualified electrical installer. |
■ To be sure that the electrical connection is adequate and in conformance with the |
National Electrical Code, ANSI/NFPA |
ordinances. |
The National Electric Code requires a |
after 1996, dryer circuits involved in remodeling after 1996, and all mobile home |
installations. |
A copy of the above code standards can be obtained from: National Fire Protection |
Association, One Batterymarch Park, Quincy, MA 02269. |
■ To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical |
supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) |
on a separate |
breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in |
the neutral or grounding circuit. |
■ Do not use an extension cord. |
■ If codes permit and a separate ground wire is used, it is recommended that a qualified |
|
|
|
| 14" max.* | 48 in. 2 * | |
|
|
|
| (35.6cm) | ||
18"* |
|
|
|
|
| (310 cm2 ) |
|
|
|
|
|
| |
(45.7 cm) |
|
|
|
|
|
|
|
|
|
|
|
| 24 in.2 * |
|
|
|
|
|
| (155 cm2 ) |
1" | 29" | 1" | 1"* | 29¼" | 5" |
|
(2.5 cm) | (73.7 cm) | (2.5 cm) | (2.5 cm) (74.3 cm) (12.7 cm) | |||
| A |
|
| B |
|
|
3"* (7.6 cm)
3"* (7.6 cm)
C
electrician determine that the ground path is adequate. |
Electrical Connection
To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.
■This dryer is manufactured ready to install with a
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
*Required spacing
5
