TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.amana.com/help

for assistance and to possibly avoid a service call.

If you experience

Possible Causes

Solution

Error Code Appears in Display

Once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.

 

“Sd” (Excess suds)

Excessive suds in washer. Washer is

Allow the washer to continue. Use only HE detergent.

 

appears in display

running a suds reduction routine.

Always measure detergent, and base detergent quantity on

 

 

 

load size. Follow detergent manufacturer’s instructions.

 

 

 

 

 

 

F8 followed by E1 (water

Check for proper water supply.

Both hoses must be attached and have water flowing to the

 

supply error) appears in

 

inlet valve.

 

display

 

 

 

 

Both hot and cold water faucets must be on.

 

 

 

 

 

 

 

 

 

 

 

Inlet valve screens on washer may be clogged.

 

 

 

 

 

 

 

 

Remove any kinks in the inlet hose.

 

 

 

 

 

 

 

 

Touch POWER once to clear the code. Then touch POWER

 

 

 

again to restart washer. If code appears again, call for service.

 

 

 

 

 

 

F9 followed by E1 (drain

Check plumbing for correct drain

Check drain hose for proper installation.

 

pump system error)

hose installation. Drain hose extends

 

 

 

Make sure the drain hose is not kinked, pinched, or blocked.

 

appears in display

into standpipe farther than 412"

 

 

(114 mm).

Remove any clogs from drain hose.

 

 

 

 

 

 

 

 

Use drain hose form and securely attach to drainpipe or tub.

 

 

 

 

 

 

 

 

Lower drain hose if the end is higher than 96" (2.4 m) above

 

 

 

the floor.

 

 

Not using HE detergent or using too

Use only HE detergent. Always measure detergent and follow

 

 

much HE detergent.

manufacturer’s directions based on load size and soil level.

 

 

 

 

 

 

F5 followed by E2 (door

Washer door not locking.

Touch POWER to cancel the cycle. Make sure the door is

 

will not lock) appears in

 

closed completely and latching. Check for items in the washer

 

display

 

drum that may be keeping the door from closing completely.

 

 

 

 

 

 

F7 followed by E1 (motor

Motor is having difficulty turning

Washer is tightly packed. Remove some items. See “Cycle

 

drive error) appears in

the drum.

Guide” for load size recommendations. Make sure that all

 

display

 

shipping materials have been removed. See the Installation

 

 

 

Instructions.

 

 

 

 

 

 

“rL” (remove load)

Load detected in drum during Clean

Remove items from washer drum and restart Clean Washer

 

appears in display

Washer with affresh® cycle.

with affresh® cycle.

 

 

 

 

 

 

Washer making error

Door has not been opened and closed

This code may appear when the washer is first turned on.

 

beeps

for at least 3 cycles.

Open and close the door to clear the display.

 

 

 

 

 

 

Washer beeps when

Door not closed.

Close the door completely.

 

HOLD TO START is

 

 

 

 

touched

 

 

 

 

 

 

 

 

 

F# E# code other than

System error code.

Touch POWER once to clear the code. Then touch POWER

 

as described above

 

again to restart washer. If code appears again, call for service.

 

appears in display

 

 

 

 

 

 

 

 

 

“nt” (interrupted)

The cycle was paused or cancelled.

The washer can take 20 to 30 minutes to stop spinning and

 

appears in display

 

drain and will display this error code during that time. Touch

 

 

 

POWER once to clear the code. Then touch POWER again to

 

 

 

restart washer.

 

 

 

 

 

Clean Washer LED

The washer has run 30 wash cycles

Run the Clean Washer cycle. If the Clean Washer cycle is not

 

flashing at end of wash

and is indicating a reminder to run the

turned on, the LED will stop flashing at the end of a wash cycle

 

cycle

Clean Washer cycle.

after running 3 more regular wash cycles. After 30 more wash

 

 

 

cycles are completed, the Clean Washer LED will again flash at

 

 

 

the end of a wash cycle as a reminder.

 

 

 

 

 

13

Page 13
Image 13
Maytag W10577942B manual Troubleshooting, If you experience Possible Causes Solution, Error Code Appears in Display