McCulloch manual MODEL NUMBER MC30 PRODUCT NUMBER, Riding Mower, Install Seat, To Adjust Seat

INSTALL SEAT

1.Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to riding mower. Remove the cardboard packing and discard.

2.Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

3.Push down on seat to engage pads in slots and pull seat towards rear of riding mower.

4.Raise seat and tighten bolt and large flat washer securely.

5.Remove tape and discard.

6.Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

Slot Tape

Pad

Flat washer

Seat pan

Bolt	Tab	Adjustment
		handle

TO ADJUST SEAT

FRONT AND BACK -

•Sit in seat.

•Lift up adjustment lever and slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Release lever to lock seat in position.

Lumbar
Adjustment Knob	Adjustment Lever

LUMBAR SUPPORT -

•Loosen lumbar adjustment knob.

•Slide seat back up or down to most com- fortable position for lower back support.

•Tighten lumbar adjustment knob.

NOTE: You may now roll your riding mower off the skid. Follow the appropriate instruction below to remove the riding mower from the skid.

WARNING: Before starting, read, un- derstand and follow all instructions in the Operation section of this manual. Be sure riding mower is in a well-ventilated area. Be sure the area in front of riding mower is clear of other people and objects.

TO ROLL RIDING MOWER OFF SKID (See Operation section for location and function of controls)

1.Raise deck lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Shift unit to neutral.

4.Roll riding mower forward off skid.

RIDING MOWER

STEERING

MODEL NUMBER MC30 (96022001300)

PRODUCT NUMBER 960 22 00-13

KEY	PART
NO.	NO.	DESCRIPTION
1	532 44 20-64	WHEEL TUBE
2	812 00 00-01	E-CLIP

3532 18 89-67 WASHER, HARDENED

4532 12 17-49 WASHER, 1/4 X 3/4

5 532 43 61-81 SPINDLE, RH

6532 12 49-31 WASHER, HARDENED THRUST

7532 12 49-37 BUSHING, STEERING COLUMN

9 819 13 14-14 WASHER

10532 42 80-57 WELDMENT, LWR STRG SHAFT

11532 43 61-83 LINK, STRNG LH

12532 43 61-84 LINK, STRNG RH

13874 78 05-24 BOLT, 5/16-18 X 1 1/2

14819 11 12-16 WASHER 11/32 X 3/4 X 16 GA

16	532 43 62-82	BUSHING SNAP
15	873 80 05-00	NUT, 5/16-18
17	532 43 61-78	SUPPORT, UPPER STEERING

19817 00 05-12 BOLT, 5/16-18 X 3/4

20532 42 80-45 CLIP, RETAINER SPRING

23 532 43 77-47 ADAPTER, STEERING WHEEL

26532 42 45-51 WHEEL, STEERING

27532 44 15-06 CAP, STEERING WHEEL

28532 19 98-49 CLIP, RETAINER SPRING

29 532 43 61-80 SPINDLE LH

30532 19 32-68 CAP, HUB, AXLE

31819 34 32-10 WASHER 1-1/16 X 2 X 10GA.

32817 58 05-20 SCREW HEXWSH THD 5/16-18 X 1-3/4

34532 43 61-82 SHAFT STEERING UPPER

35532 44 20-66 BOOT LOWER STEERING WHEEL

36532 19 60-75 SHAFT EXTENSION STEERING SPLINE

37874 78 05-80 BOLT FIN HEX 5/16-18 UNC X 5 GR5

38810 04 05-00 WASHER LOCK HVY HLCL SPR 5/16

39 819 11 38-12 WASHER

41532 43 65-90 FOAM SHAFT STEERING

42532 42 10-76 PIN, 5/64 X 3/4 COTTER

43873 54 05-00 CROWNLOCK NUT 5/16-24 UNF

44 532 42 80-44 BUSHING

NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

8 37