STORAGE
RIDING MOWER
Always observe safety rules when performing any maintenance.
CHECK REVERSE OPERATION (ROS) SYSTEM
• When the engine is running with the ignition |
Immediately prepare your riding mower for storage at the end of the season or if the riding mower will not be used for 30 days or more.
WARNING: Never store the riding mower with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before stor- ing in any enclosure.
MOWER
Remove deck from mower for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.
1.Clean entire riding mower (See “CLEAN- ING” in the Maintenance section of this manual).
2.Inspect and replace belt, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual).
3.Lubricate as shown in the Maintenance section of this manual.
4.Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.
5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.
BATTERY
•Fully charge the battery for storage.
•If battery is removed from riding mower for storage, do not store battery directly on concrete or damp surfaces.
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.
•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.
•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.
•Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable al- ternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).
CYLINDER(S)
1.Remove spark plug(s).
2.Pour one ounce of oil through spark plug hole(s) into cylinder(s).
3.Turn ignition key to “START” position for a few seconds to distribute oil.
4.Replace with new spark plug(s).
OTHER
•Do not store gasoline from one season to another.
•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.
•If possible, store your riding mower indoors and cover it to give protection from dust and dirt.
•Cover your riding mower with a suitable protective cover that does not retain mois- ture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your riding mower to rust.
IMPORTANT: Never cover riding mower while engine and exhaust areas are still warm.
BRAKE OPERATION
If riding mower requires more than four (4) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced at your nearest authorized service center.
TIRES
•Maintain tire pressure at 12 PSI.
•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.
•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.
AXLE AND SPINDLES
•Front wheel axles and front spindles should be properly lubricated.
•Wheel axles and spindles should be lubricated with grease.
Spindle
Wheel Axle
OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)
Be sure operator presence and reverse operation systems are working properly. If your riding mower does not function as described, repair the problem immediately.
•The engine should not start unless the brakepedalisfullydepressed,andthedeck clutch lever is in the disengaged position.
CHECK OPERATOR PRESENCE SYSTEM
•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.
•When the engine is running and the deck clutch lever is engaged, any attempt by the operator to leave the seat should shut off the engine.
•Never operate the deck clutch lever unless you are seated in the seat.
switch in the engine "ON" position and the |
deck clutch lever engaged, any attempt by |
the operator to shift into reverse should |
shut off the engine. |
• When the engine is running with the ignition |
switch in the ROS "ON" position and the |
deck clutch lever engaged, any attempt by |
the operator to shift into reverse should |
NOT shut off the engine. |
ROS "ON" | Engine "ON" Position |
Position | (Normal Operating) |
BLADE CARE
For best results mower blades must be sharp. Replace worn, bent or damaged blades.
CAUTION: Use only a replacement blade approved by the manufacturer of your riding mower. Using a blade not approved by the manufacturer of your riding mower is hazard- ous, could damage your riding mower and void your warranty.
BLADE REMOVAL
1. Raise mower to highest position to allow access to blade.
NOTE: Protect your hands with gloves and/ or wrap blade with heavy cloth.
2.Remove blade bolt by turning counter- clockwise.
3.Install new blade with stamped "THIS SIDE UP" facing deck and mandrel as- sembly.
Mandrel
Assembly
Blade
Blade Bolt (Special)
Star
Center Hole
IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.
4. Install and tighten blade bolt securely
IMPORTANT: Special blade bolt is heat treated.
26 | 19 |
