7 - MAINTENANCE INSTRUCTIONS

7-5.SPARK PLUG

NOTE: For efficient operation of saw engine, spark plug must be kept clean and properly gapped.

1.Push STOP switch down.

2.Remove air cleaner cover.

3.Disconnect the wire connector (G) from the spark plug

(H) by pulling and twisting at the same time (Figure 7- 5A).

4.Remove spark plug with spark plug socket wrench.

DO NOT USE ANY OTHER TOOL.

5.Check electtrode gaps with wire feeler gauge and set gaps to .025” (.635mm) if necessary.

6.Reinstall a new spark plug.

NOTE: A resistor spark plug must be used for replacement (McCulloch part no. 9295-310502).

NOTE: This spark ignition system meets all requirements of the Canadian Interference-Causing Equipment Regulations.

G

H

7-5A

7-6.CARBURETOR ADJUSTMENT

The carburetor was pre-set at the factory for optimum per- formance. If further adjustments are necessary, please take your unit to the nearest Authorized Service Center list- ed in the Yellow Pages.

7-7.STORING A CHAIN SAW

CAUTION

Never store a chain saw for longer than 30 days without performing the following procedures.

Storing a chain saw for longer than 30 days requires stor- age maintenance. Unless the storage instructions are fol- lowed, fuel remaining in the carburetor will evaporate, leav- ing gum-like deposits. This could lead to difficult starting and result in costly repairs.

1.Remove the fuel tank cap slowly to release any pres- sure in tank. Carefully drain the fuel tank.

2.Start the engine and let it run until the unit stops to remove fuel from carburetor.

3.Allow the engine to cool (approx. 5 minutes).

4.Using a spark plug wrench, remove the spark plug.

5.Pour 1 teaspoon of clean 2-cycle oil into the combus- tion chamber. Pull starter rope slowly several times to coat internal components. Replace spark plug (Figure 7-7A).

NOTE: Store the unit in a dry place and away from possi- ble sources of ignition such as a furnace, gas hot water heater, gas dryer, etc.

7-7A

7-8.REMOVING A UNIT FROM STORAGE

1.Remove spark plug.

2.Pull starter rope briskly to clear excess oil from com- bustion chamber.

3.Clean and gap spark plug or install a new spark plug with proper gap.

4.Prepare unit for operation.

5.Fill fuel tank with proper fuel / oil mixture. See Fuel and Lubrication Section.

16

Page 17
Image 17
McCulloch MS4016PAVCC, MS4018PAVCC Spark Plug, Carburetor Adjustment, Storing a Chain SAW, Removing a Unit from Storage

MS4016PAVCC, MS4018PAVCC specifications

The McCulloch MS4016PAVCC and MS4018PAVCC are two notable chainsaws designed to combine power, efficiency, and user-friendly features. Both models are well-suited for a variety of tasks, ranging from occasional home use to more demanding cutting jobs, making them ideal for homeowners and DIY enthusiasts.

The MS4016PAVCC features a 16-inch guide bar, while the MS4018PAVCC is equipped with an 18-inch guide bar. This difference in bar length accommodates different cutting requirements, with the MS4018PAVCC providing the ability to handle larger logs and thicker branches. Both models are powered by a robust 40cc engine, delivering impressive cutting performance without sacrificing weight—making them manageable for extended use.

One of the most notable features of the McCulloch MS4016PAVCC and MS4018PAVCC is their high-quality chain system, designed for smooth and efficient cutting. The low-vibration technology incorporated into both chainsaws minimizes fatigue for the user, enabling longer cutting sessions with increased comfort. Additionally, the automatic chain lubrication system ensures that the chain remains well-lubricated during operation, promoting longevity and optimal performance.

Ergonomically designed, both models come equipped with soft-grip handles that enhance user comfort. Easy-access controls allow for convenient operation and adjustments on-the-go. The quick-start system reduces the effort needed to start the engine, making these chainsaws ideal for a range of users, from novice to experienced.

Safety features are a priority in the MS4016PAVCC and MS4018PAVCC models. They include a chain brake designed to prevent accidental chain rotation, reducing the risk of injuries during operation. Additionally, the design includes a front hand guard and an easy-to-operate throttle lever for enhanced safety.

Overall, the McCulloch MS4016PAVCC and MS4018PAVCC chainsaws are a blend of power, user-friendliness, and safety. With their durable build, efficient performance, and comfortable handling, they are poised to meet the needs of those looking to tackle cutting tasks around the home or yard. With McCulloch's commitment to quality and innovation, these chainsaws stand out as reliable companions for any cutting job.