Fig. 6: Attach cradle to mounting arm.
Fig. 8b: Attach the viewfinder bracket to the reflector optical tube assembly.
GETTING STARTED
Packing List
Getting the telescope ready for first observations requires only a few minutes. When first open- ing the packing box, note carefully the parts listed on your packing list or giftbox.
How to Assemble Your Telescope
The telescope attaches directly to the tripod. The telescope in this way is mounted in an “Altazimuth”
1.Open the tripod: After removing the field tripod from its shipping carton, stand the tripod vertically, with the tripod feet down and with the tripod still fully collapsed. Gently pull the legs apart to a fully open position.
2.Attach the tray to the tripod: Place the tray (19, Fig. 1) over the inner support strut that contains two bolt holes. Line up the bolts holes on the tray with the bolt holes on the strut. Slide the two included bolts through the top of bolt holes (18, Fig. 1) and tighten the bolts with the included wing nuts on the bottom side of the tray (Fig. 3). Tighten to a firm feel only.
Note: The tray does not have to be removed when you collapse the tripod at the end of a viewing session.
3.Secure the tripod: Turn the center tripod lock knob (Fig. 4) to help stabilize and secure the tripod.
Caution: Make sure that you loosen the tripod lock knob before collapsing the tri- pod.
4.Attach the mounting arm assembly to the tripod base: First note the three pads in the tripod base (23, Fig. 1) and three pads on the mounting arm assembly (16, Fig. 1). These pads allow the mounting arm assembly to move more easily inside the base.
Place the mounting arm assembly into the tripod base and continue to hold onto the arm assembly. With your other hand, reach underneath the base and thread the mounting lock knob (26, Fig. 1) through the tripod base and into the mounting arm assembly. Tighten to a firm feel only; do not overtighten. While observing, you may wish to loosen this knob and rotate the mounting arm assembly and optical tube (see step #8) on the horizontal axis.
5.Remove the optical tube assembly from the cradle rings: The optical tube assembly is shipped with the cradle rings attached. The rings need to be removed before they can be attached to the mounting arm. Loosen the cradle lock knob (14, Fig. 1) until you can open the cradle rings. Remove the optical tube assembly (13, Fig. 1) from the cradle rings.
6.Remove 4 screws from the mounting arm shaft: Locate the four screws on the mount- ing shaft. Remove the screws using a "+" (Phillips head) screwdriver. Set the screws aside.
7.Attach the cradle to the mounting arm: Line up the cradle with the mounting arm shaft. The cradle contains a molded "key" that fits into a slot on the shaft. Line up the key and the slot, and slide the cradle onto the shaft. This automatically lines up the mating threads on the cradle with the ones on the shaft. Replace the four screws into the mating threads using the Phillips head screwdriver (Fig. 6). The key and slot on the shaft set limit stops for the telescope so that it doesn't strike the base or pass beyond approximately 90° upright when you use the Autostar handbox.
8.Attach and balance the optical tube: Replace the optical tube into the cradle ring. Tighten the cradle ring lock knob so that it holds the optical tube loosely; do not tighten the cradle ring lock knob at this point. Slide the tube back and forth until you find a position where the tube remains horizontal (i.e., without slightly tipping up or down). Tighten the cra- dle rings lock knob to a firm feel. See Fig. 7. Adjust the length of the tripod legs to a com- fortable viewing height using the leg locks (21, Fig. 1).
9.Attach the viewfinder bracket: Attach the bracket to the optical tube as shown in Fig 8a (the refractor viewfinder) or 8b (the reflector viewfinder). Using a Phillips head screwdriver, thread the two attachment screws in the bracket (these screws are placed inside the bracket at the factory) into the mating threads located on the optical tube.
11
Fig.8a:Attach the
Fig.7:Attach and bal-
