Remote Voltage/Amperage Control | Miller Electric 300 P specification

6-5. Remote Voltage/Amperage Control

1

In Example:

Min = 20 A DC

Max = 205 A DC

1 Remote 14 Receptacle RC14

Connect optional remote control to RC14 (see Section 5-9).

.When a remote control is connected to the

Remote receptacle, the Auto Sense Re- mote feature automatically switches volt- age/amperage control to the remote con- trol. When a device is connected to the Re- mote receptacle, remote voltage/amper- age control is always available regardless of the position of the Process/Contactor switch.

Connect Remote

Control To Remote

Receptacle RC14

Connect Remote

Control To Remote

Receptacle RC14

Adjust Optional Remote Control to 100%

Set TIG or STICK Process

Adjust Optional Remote

Control to desired

weld output

Set WIRE Process

Set V/A Control

To Desired Maximum

Weld Output Using Weld

Meters

Max (205 A DC)

Min (20 A DC)

Adjust Optional Remote

Control to desired

weld output

Weld meters will always show the combined main and remote control setting and machine welds at nominal output setting of the meter.

Weld meters show preset output when not welding.

0774 / Ref.217 357−B / 803 562

OM-4433 Page 28

Image 32

Miller Electric 300 P manual Remote Voltage/Amperage Control

Contents

OM-4433218 314K ProcessesDescription File Engine Drive From Miller to You Table of Contents Warranty Symbol Usage Arc Welding Hazards Engine Hazards Compressed Air Hazards Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïe LA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessures’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électrique LE Soudage À L’ARC risque de provoquer des interférences Pour les moteurs à essencePour les moteurs diesel Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone Std − Definitions− 50 h Std Manufacturer’s Rating Label Symbols And Definitions Dimensions, Weights, And Operating Angles − SpecificationsWeld, Power, And Engine Specifications Stick Mode MIG ModeTIG Mode Volt-Ampere Curves Curve shows typical fuel use under weld or power loads Exceeding duty cycle can damage unit and void warrantyFuel Consumption Duty Cycle And Overheating AC Generator Power Curve 150 125 100 − Installation Installing Welding GeneratorSee -2for lifting eye rating See -2for mounting information Grounding Mounting Welding Generator Installing Exhaust Pipe Tools Needed 1/2Stop engine and let cool Point exhaust pipe in desired di Activating The Dry Charge Battery If Applicable Connecting The BatteryDo not overfill battery cells Close door after connecting battery Coolant Recovery Tank Engine Prestart ChecksFuel Do not use gasoline. Gasoline will damage engine Oil Connecting To Weld Output Terminals Stick and TIG WeldingMIG and Fcaw Welding Stop engine Selecting Weld Cable Sizes 150 ft 200 ft 250 ft350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Stop engine before Connecting To Remote 14 Receptacle RC14 Socket Information − Operating Welding Generator Front Panel Controls See Section Description Of Front Panel Controls See Section Process/Contactor Switch Process/Contactor Switch Settings Lift-ArcStart Procedure Lift-Arc Start Method TouchDo not Strike Like a Match Lift-Arc t TIG Remote Voltage/Amperage Control At least once a month, run engine at Generator Power Receptacles− Operating Auxiliary Equipment − Maintenance & Troubleshooting Routine Maintenance Maintenance Label Servicing Air Cleaner By the warrantyTo clean air filter Do not clean housing with air hose Servicing Engine Cooling System Inspecting And Cleaning Optional Spark Arrestor MufflerStop engine and let cool. Reinstall cleanout plug Adjusting Engine Speed On Standard Models MaximumDo not set engine speed higher Stop engine. Close door Engine Speed Adjustment Weld/Power Speed Adjust- mentEngine Speed No Load Rpm max 62.6 Hz 1250 rpm 41.6 Hz Servicing Fuel And Lubrication Systems To change oil and filterTo replace primary canister fuel filter To drain water from fuel system Overload Protection Checking Generator Brushes Replace Damaged Brushes Help 25 Display Voltmeter/Ammeter Help DisplaysHelp 20 Display Troubleshooting Welding Generator Power Engine Check for obstructed throttle solenoid Material Thickness Reference Chart − Electrical Diagrams Circuit Diagram For Welding Generator 219 228−D Welding Generator − RUN-IN ProcedureWetstacking Run-In Procedure Using Load Bank Procedure at less thanStop engine Do not touch hot exhaust From flammables Do not Perform Run-In Procedure Using Resistance Grid Bank/gridFrom flammables Do not perform run-in − Generator Power Guidelines Has this symbolSelecting Equipment Grounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Use ground device as stated Electrical codes Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts Amperes 108 -2 107 101 102 103 100 104 106 105 − Parts List109 81 Fig 7372 71 67 66 65 PC3 Dia Part Description Quantity Mkgs Batt Panel, Front w/Components Panel, Front w/Components -1Item FUEL/HM Control Panel Generator Rectifier Assembly Wiring Harnesses Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s