Mounting Welding Generator | Miller Electric 400P, 500 X specs

5-3. Mounting Welding Generator
	! Do not weld on base. Weld-
	ing on base can cause fuel
	tank fire or explosion. Weld
	only on the four mounting
Supporting The Unit	brackets or bolt unit down.
Supporting The Unit

	NOTICE − Do not mount unit by
	supporting the base only at the four
	mounting brackets. Use cross-
2	supports to adequately support unit
2	and prevent damage to base.

			Mounting Surface:
			1	Cross-Supports
		OR	2	Mounting Brackets (Supplied)
		OR	Mount unit on flat surface or use
			Mount unit on flat surface or use
			cross-supports to support base.
			Secure unit with mounting brack-
			ets.
1			3	1/2 in Bolt And Washer
				(Minimum − Not Supplied)
			4 3/8-16 x 1 in Screws
				(Supplied)
			To Bolt Unit In Place:
			Remove hardware securing the
	1		four mounting brackets to the base.
	1		Reverse brackets and reattach to
			Reverse brackets and reattach to
			base with original hardware.
			Mount unit to truck or trailer with 1/2
Using Mounting Brackets			in (12 mm) or larger hardware (not
			supplied).

To Weld Unit In Place:

2

Welding Unit In Place

Bolting Unit In Place

23

4

Tools Needed: 9/16 in

Weld unit to truck or trailer only at the four mounting brackets.

install3 2007−046 803 274 / 200 864-A / 803 602

OM-4421 Page 22

Image 28

Miller Electric 400P, 500 X manual Mounting Welding Generator

Contents

OM-4421215 075Q ProcessesDescription File Engine Drive From Miller to You Table of Contents − Maintenance & Troubleshooting Standards DirectivesDecrot1/07 Manufacturer European Contact Notified Body Decrotsound6/05 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous Buildup of GAS can injure or killARC Rays can burn eyes and skin Welding can cause fire or explosion Engine Hazards Compressed Air Hazards Welding Wire can cause injury HOT Parts can cause burns and injuryFire or Explosion hazard Falling Unit can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer Indique des instructions spécifiques DES Pièces Chaudes peuvent provoquer des brûlures graves LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un in cendie ou une explosion LE Bruit peut affecter l’ouïe ’EXPLOSION DE LA Batterie peu DES Organes Mobiles peuvent pro voquer des blessures ’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion LE Surchauffement peut endom- mager le moteur électrique DES Organes Mobiles peuvent provoquer des blessuresLES Fils DE Soudage peuvent provoquer des blessures ’EMPLOI Excessif peut Proposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF En ce qui concerne les implants médicaux − 50 h Std − DefinitionsStd Manufacturer’s Rating Labels Symbols And Definitions Some symbols are found only on export products Weld, Power, And Engine Specifications − SpecificationsDimensions, Weights, And Operating Angles Volt-Ampere Curves For CC Models Stick Mode MIG ModeTIG Mode Volt-Ampere Curves For CC/CV Models Duty Cycle And Overheating Fuel Consumption100% Duty Cycle At 400 Amperes AC Generator Power Curve Optional Three-Phase Generator Curves12 kVA/kW Single-Phase AC Output No Weld Load 15 kVA/kW Three-Phase AC Output No Weld Load − Installation Installing Welding GeneratorLocation/Airflow Clearance Grounding1 Using Lifting Eye Mounting Welding Generator Installing Exhaust Pipe Stop engine and let cool Activating The Dry Charge Battery If Applicable Connecting The Battery Coolant Recovery Tank Engine Prestart Checks Connecting To Weld Output Terminals Stick and TIG WeldingMIG and Fcaw Welding Stop engine Connecting to Weld Selecting Weld Cable Sizes150 ft 200 ft 250 ft 350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Connecting To Remote 14 Receptacle RC14 On CC/CV Models Socket OM-4421 − Operating Welding Generator − CC Models Front Panel Controls For CC Models See Section Engine Starting Controls To StartEngine Gauges And Meters Weld Controls Weld Control/Arc Condition Information Label Remote Amperage Control On CC Models OptionalExample Combination Remote Amperage Control Stick OM-4421 − Operating Welding Generator − CC/CV Models Front Panel Controls For CC/CV Models See Section Electric shock can kill Voltage/Amperage Adjust Switch And Remote 14 Receptacle14 AC/DC Voltmeter Optional Process/Contactor Switch On CC/CV Models Process/Contactor Switch Settings Remote Voltage/Amperage Control On CC/CV Models Optional Example Combination Remote Amperage Control TIG − Operating Auxiliary Equipment Volt And 240 Volt ReceptaclesAt least once a month, run en If a Supplementary Rear Of Panel Three-Phase Power ConnectionClose panel opening if no connections are made to generator 240 V 15 a AC South African Receptacle RC1 Optional Generator Power ReceptaclesSupplementary Protector CB2 Supplementary Protector CB3 − Maintenance & Troubleshooting Maintenance Label Routine Maintenance Checking Generator Brushes Servicing Air Cleaner To clean air filter Inspecting And Cleaning Optional Spark Arrestor Muffler Adjusting Engine Speed Weld/Power Speed AdjustmentEngine Speed No Load Standard Model Idle Speed Ad- justment Servicing Fuel And Lubrication Systems To change oil and filterTo replace primary fuel filter While draining fuel tank Overload Protection Troubleshooting Welding − CC Models Welding − CC/CV Models Standard Generator Power Optional Three-Phase Generator Power CC/CV Models Only Engine Welding Symbols − Electrical Diagrams Circuit Diagram For CC Welding Generator 223 522-B Circuit Diagram For CC/CV Welding Generator 223 523-B Wetstacking − RUN-IN ProcedureWelding Generator Keep exhaust and pipe away Run-In Procedure Using Load BankFrom flammables Run-In Procedure Using Resistance Grid Specifications section in thisJust generator A/V control so Manual − Generator Power Guidelines Selecting EquipmentGrounding Generator To Truck Or Trailer Frame Electrically Bond Generator Grounding When Supplying Building Systems How Much Power Does Equipment Require?Use ground device as stated in electrical codes Amperes x Volts = Watts Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible − Parts List 128 93 −6 105 104 100 101 102 103 Main Assembly 010 Figures 13-2 Figures 13-4 Control Box Assembly − CC Models 087 Control Box Assembly − CC/CV Models Control Box Assembly − CC/CV Models -1Item TD1 214 Panel, Front w/Components − CC Models 3634 Panel, Front w/Components − CC Models -1Item Panel, Front w/Components − CC/CV Models 40 39 Panel, Front w/Components − CC/CV Models -1Item 170 Hardware is common Not available unless listed 34 36 27 26 602 SCREW, .312−18x .75 hexwhd.66d stl pld slffmg tap−rw 601 Main Rectifier Assembly Wiring Harnesses Harness, receptacle auxiliary power export models includes PLG4Page Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s