![](/images/new-backgrounds/1209880/20988055x1.webp)
6-11. Reset Mode
RST
NO
Enter reset mode by turning power On and pressing the Program Push Button until the RST NO message is displayed. RST NO message will not display until after the
.Reset mode is not active when Program Lock is enabled.
The reset mode allows the operator to reload factory program settings for all eight active programs in the unit.
.System configuration data will be lost during the Reset operation.
RST YES ![](/images/new-backgrounds/1209880/20988055xi2.webp)
![](/images/new-backgrounds/1209880/20988055xi3.webp)
![](/images/new-backgrounds/1209880/20988055xi4.webp)
![](/images/new-backgrounds/1209880/20988055xi5.webp)
![](/images/new-backgrounds/1209880/20988055xi6.webp)
![](/images/new-backgrounds/1209880/20988055xi7.webp)
![](/images/new-backgrounds/1209880/20988055xi8.webp)
![](/images/new-backgrounds/1209880/20988055xi9.webp)
![](/images/new-backgrounds/1209880/20988055xi10.webp)
![](/images/new-backgrounds/1209880/20988055xi11.webp)
RST YES
CYCL![](/images/new-backgrounds/1209880/20988055xi22.webp)
PWR ![](/images/new-backgrounds/1209880/20988055xi24.webp)
![](/images/new-backgrounds/1209880/20988055xi25.webp)
![](/images/new-backgrounds/1209880/20988055xi26.webp)
![](/images/new-backgrounds/1209880/20988055xi27.webp)
![](/images/new-backgrounds/1209880/20988055xi28.webp)
![](/images/new-backgrounds/1209880/20988055xi29.webp)
![](/images/new-backgrounds/1209880/20988055xi30.webp)
![](/images/new-backgrounds/1209880/20988055xi31.webp)
![](/images/new-backgrounds/1209880/20988055xi32.webp)
![](/images/new-backgrounds/1209880/20988055xi33.webp)
Rotate Adjust knob to change NO
to YES.
Press the Arc Control button to
confirm the reset.
The reset message is displayed for 2 seconds while factory program settings are being reloaded.
During the reset mode the following factory default programs are loaded into the unit:
Cycl Pwr message appears on the display
when programs complete loading.
Turn power off, wait 10 seconds, and turn power back on again to complete the reset operation.
.After Reset is complete, be sure to load
appropriate programs that contain the correct wire size, process, and shielding gas for the welding operation
Program 1 | Pulse |
| .035 Mild Steel |
| 90% Argon, 10% CO2 |
Program 2 | MIG |
| .035 Mild Steel |
| 75% Argon, 25% CO2 |
Program 3 |
|
| .035 Mild Steel |
| 90% Argon, 10% O2 |
Program 4 | Pulse |
| .045 Mild Steel |
| 90% Argon, 10% CO2 |
Program 5 | MIG |
| .045 Mild Steel |
| 75% Argon, 25% CO2 |
Program 6 | |
| .045 Mild Steel |
| 90% Argon, 10% O2 |
Program 7 | Pulse |
| .052 Mild Steel |
| 90% Argon, 10% CO2 |
Program 8 | MIG |
| .052 Mild Steel |
| 75% Argon, 25% CO2 |
198 993 / 803