owners manual

A general guideline for the recommended height would be approximately 6 feet. But, there might be situations when this is not possible. If an OMNI series speaker is installed on the wall above six feet, position it so the grille faces downward. If the OMNI series speaker is positioned below six feet, position it so the grille faces upward.

The OMNI 50, OMNI 60, OMNI FX and OMNI CC are equipped with rubber isolation feet. Remove the adhesive backing on these feet and attach them to the bottom of the speaker.

CONNECTIONS

CEILING MOUNT

The OMNI FX can be ceiling mounted by using the Macromount bracket and NOT the wall mount clip provided. The OMNI FX, OMNI 50, OMNI 60 and OMNI CC are equipped with an insert to accommodate the optional Macromount bracket for ceiling mount options. The versatile Macromount bracket provides the sturdiest ceiling mount and its terminal fits the 3/8”-16 thread insert located at the back of the OMNI models mentioned. Just remove the rubber Mirage logo on the input terminal in back of the speaker to expose the insert.

Orient the speaker so the OMNITECH module, or portion of the speaker that houses the drivers, faces the listening area.

BOOKSHELF/ENTERTAINMENT UNIT PLACEMENT

The small size and Omnipolar dispersion of the versatile OMNI 50, OMNI 60 and OMNI CC center channel speakers permits them to be easily placed, among other places, in a bookshelf. If this is your preferred placement, affix the isolating pads provided to the bottom of the speaker to help isolate the speaker from the shelf and eliminate any transference of resonance. To maximize the Omnipolar dispersion potential, bring the speaker as close to the front of the cabinet as possible.

FEET

The OMNI 250 and OMNI 260 come equipped with a foot kit to improve the bass performance of your speaker. This kit should include:

2

- Front Feet

2

- Round head machine bolts

4

- Nuts

2

- Regular length Spikes for the front feet

The Mirage OMNI series is equipped with high quality binding posts that permit the use of banana plugs, spades, or a bare wire connection. Turn them counterclockwise to loosen, clockwise to tighten.

Connect the speaker wire from the positive (RED +) terminal on the amp to the positive (RED+) terminal on the speaker. Connect the negative (BLACK-) terminal on the amplifier to the negative (BLACK-) terminal

on the speaker. See diagram 1.

OMNI 260

System Type:

Magnetically Shielded Omnipolar Tower

Frequency Response:

35Hz-20KHz, +/- 3dB

 

 

Tweeter:

1” (25mm) PTH™ Pure Titanium Hybrid

 

 

Woofer:

Two 6 1/2 “ Polypropylene Titanium Deposit Hybrid

 

 

Crossover Points:

2KHz

 

 

Room Efficiency:

93dB

 

 

Impedance:

8-ohms nominal, 4-ohms minimum

 

 

Recommended

 

Amplifier Power:

Up to 200-watts RMS/Channel

 

 

Inputs:

High Quality 5-way Terminals

 

 

Dimensions:

in. 42 x 9 x 15

H x W x D

cm. 107 x 23 x 38

 

 

Finishes:

Black and cherry

 

 

Weight:

55 lbs / speaker

 

25 kg / speaker

 

 

2 - Adhesive rear feet

2 - Very long spikes for the rear feet

 

 

 

4 - 1” wood screws

4 - washers

 

OMNI 250

 

4 - Rubber bumpers

1 - Spacer-supplied only with the OMNI 260

 

System Type:

Magnetically Shielded Omnipolar Tower

 

 

 

 

 

 

Follow these instructions to attach the feet

 

Frequency Response:

40Hz-20KHz, +/- 3dB

 

 

 

 

Tweeter:

1” (25mm) PTH™ Pure Titanium Hybrid

to your speaker: See diagram 2.

 

 

 

 

 

Woofer:

Two 5 1/2” Polypropylene Titanium Deposit Hybrid

1)

Lay the speaker on it’s back and position the front feet over the

 

 

 

 

 

pre-drilled holes.

 

 

Crossover Points:

2KHz

2)

Insert the 2 round head machine bolts into the two larger holes,

 

 

 

 

Room Efficiency:

93dB

 

one in each foot

 

 

 

 

 

 

 

Impedance:

8-ohms nominal, 4-ohms minimum

3)

If you have the OMNI 260, place the spacer in the open area

 

 

 

 

 

Recommended

 

 

between the two feet

 

 

 

 

 

 

Amplifier Power:

Up to 150-watts RMS/Channel

4)

Insert the four wood screws into the smaller holes, two in each foot.

 

 

 

 

 

Inputs:

High Quality 5-way Terminals

 

For the OMNI 260, these screws will also secure the spacer.

 

5)

To attach the rear feet, first thread a nut onto the very long spike, then

 

Dimensions:

in. 38 x 8 x 13

 

slide a washer over the shaft of the spike so it rests on the nut. Then,

 

H x W x D

cm. 97 x 20 x 33

 

insert the spike through the foot. Once properly located over the

 

 

 

 

 

Finishes:

Black and cherry

 

insert where the spike will fit, remove the adhesive backing on the foot

 

 

 

 

 

 

 

Weight:

45 lbs / speaker

 

and attach it to the speaker.

 

6)

You may now attach either the regular length spikes to the front

 

 

20.45 kg / speaker

 

 

 

 

 

 

 

feet,preferred on carpeted floors or the rubber bumpers preferred for

 

 

 

 

wood or other potentially easily damaged surfaces.

 

 

 

7)

Place the speaker upright and repeat for the second speaker.

3

 

 

 

 

 

 

 

Page 2 Page 4
Page 3
Image 3
Mirage Loudspeakers OMNI 60, OMNI 50 Connections Ceiling Mount, Feet, Omni, Follow these instructions to attach the feet
Page 2 Page 4

OMNI 60, OMNI 50, OMNI CC specifications

The Mirage Loudspeakers OMNI CC, OMNI 50, and OMNI 60 represent a leap forward in audio technology, designed to deliver high-quality sound while enhancing the home theater experience. Each model features distinct characteristics that cater to varying needs, yet all embody the brand’s commitment to superior sound reproduction.

Starting with the OMNI CC, this center channel speaker is engineered for precise dialogue clarity and immersive soundstage capabilities. Its unique design allows for a broader sweet spot, making it easier to experience clear audio from anywhere in the room. The OMNI CC utilizes proprietary technologies like the OMNIDIRECTIONAL soundfield, which disperses sound in a 360-degree pattern. This feature ensures that whether you're sitting directly in front of the speaker or off to the side, the audio experience remains consistent and impactful.

Next in line, the OMNI 50 is a compact yet powerful bookshelf speaker that excels in versatility. It features a 5.25-inch polypropylene woofer, which delivers deep bass response without sacrificing mid-range clarity. Integrated with a 1-inch aluminum dome tweeter, the OMNI 50 offers crisp highs, making it an ideal choice for both music and movie enthusiasts. The distinctive design not only enhances acoustic performance but also adds a touch of elegance to any room.

Then there’s the OMNI 60, which elevates the performance further with a more robust build. This floor-standing speaker is equipped with dual 6.5-inch woofers that provide extended low-frequency output, perfect for those who crave a full-bodied sound experience. The OMNI 60 also employs advanced crossover technologies to ensure seamless transitions between frequencies, which enhances the overall clarity and balance of audio playback.

Across the board, these speakers are built with high-quality components and finished with a sleek aesthetic, making them as much a visual centerpiece as they are a functional audio solution. With their advanced technologies and thoughtful engineering, the Mirage Loudspeakers OMNI series is set to redefine expectations in home audio systems, offering immersive soundscapes for any listener. Whether you're enjoying a cinematic experience or simply listening to your favorite playlist, the OMNI CC, OMNI 50, and OMNI 60 speakers deliver exceptional audio quality that enhances every moment.
Top Page Image Contents