Mitsubishi Electronics FL7000 Indicators

EN-37

Indicators

POWER

Steady

green

or

Steady red

Steady red

Steady

green

Steady red

Steady red

Blinking

green/red

Blinking

green/red

STATUS

Blinking orange

Blinking green

Blinking green/red

Blinking red

Steady red

Off

Steady

or

Blinking

CONDITION

Abnormal temperature

• The ventilation grilles are clogged with dust or dirt.

• The room temperature is high.

• The ﬁlter is dirty.

The protection circuit is working or the lamp is in an

abnormal condition.

The lamp or cover isn’t closed.

Abnormal.

POSSIBLE SOLUTION

• Clean the ventilation grilles.

• Relocate the projector to a cooler place.

• Clean the ﬁlter.

• Wait until the STATUS indicator goes out,

then press the POWER button.

• If the above solution is not effective,

replace the lamp.

Replace the lamp.

Change with a new lamp if this problem

recurs.

Close the cover correctly.

Contact your dealer.

Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be

shorted.

*

1

*

2

When LAMP MODE is set to STANDARD, this duration will be shorted up to 2000 hours.

Lamp operation time warning. (Total lamp operation time

reached 3000 hours*1 while the power was on.)

Lamp operation time warning. (Total lamp operation time

reached 3000 hours*1 while the power was off.)

Lamp operation time warning. (Total lamp operation time

reached 4000 hours*1*2 while the power was off.)

This projector has 2 indicators, each of which shows the operation condition of the projector.

The following offer solutions to possible problems. If these problems persist, turn the projector off and consult your

dealer.

Normal condition

Abnormal condition

STATUS indicator

POWER indicator

POWER

Steady

red

Steady

green

S TA TUS

Off

Steady

green

CONDITION

Stand-by

Lamp stand-by for power-on (about 1 minute)

The power is on. (Normal condition)

NOTE

The power cannot be turned off by pressing

the POWER button.

For the ﬁrst one minute, the power cannot be

turned on by pressing the POWER button.

Steady

green

Blinking

Lamp stand-by for power-off (about 2 minutes)

r

green

Contents

Main CAUTION CAUTION WARNING: CAUTION: NOTE: Contents Important safeguards Important safeguards (continued) Preparing your projector 1 2 3 Checking accessories Inserting the batteries into the remote control Overview Control area Terminal board Preparating your projector (continued) Bottom side Remote control About the laser beam Using the remote control Operational range of the remote control Reception angle Using the wired remote control Setting up your projector Setting up the screen Screen size and projection distance When the aspect ratio of the screen is 16:9 When the aspect ratio of the screen is 4:3 Setting up your projector (continued) LENS SHIFT button Adjusting the projection angle When ne streaks are seen on projected images When projected images are distorted to a trapezoid Setting up your projector (continued) Front projection, ceiling mounting Caution: Important: Rear projection Viewing computer images A. Connecting the projector to a computer About DDC B. Plugging the power cord C. Projecting images Preparation: Remove the lens cap. To stop projecting: AV mute AUTO POSITION button When connecting to a notebook computer: Viewing video images Connecting to a video player, etc. A. Connecting the projector to video equipment Connecting to video equipment having a HDMI terminal or DVI-D terminal Projector + DVD player or HDTV decoder B. Plugging in the power cord C. Projecting images Preparation: Remove the lens cap. To stop projecting: Volume from the speaker Setting the aspect ratio Menu operation Menus are not displayed when no signal is supplied to the projector. Available settings in the menus How to set the menus: Page Page 4. SIGNAL menu SIGNAL - RESOLUTION (MEMORIZE) menu SIGNAL - USER menu ITEM SETTING FUNCTION C Page Adjusting projected images To adjust the brightness (CONTRAST and BRIGHTNESS): To adjust the color (COLOR and TINT): To sharpen or soften the projected image (SHARPNESS): To adjust the tone of white (COLOR TEMP.): About color temperature Color Enhancer How to adjust the computer image How to adjust the image supplied from the computer using the menu: Simple method to adjust the image position LPF (Progressive lter) Setting of the image displayed during startup or muting Setting procedure Advanced features Password function W S=1, X=2, T=3, W=4) W S=1, X=2, T=3, W=4) Split Freeze Mouse remote control Projector + computer with USB connector Operation USB Supervising and controlling by computer Major functions Connection Using the User Manual Indicators POWER STATUS CONDITION Abnormal condition Terminal cover (with anti-theft alarm device) Procedure for changing batteries Replacing the lamp Interval of lamp replacement Replacing the lamp (continued) To replace the lamp: Maintenance Cleaning of the air- lter Cleaning of the projector and the ventilation slots Cleaning of the lens Troubleshooting Page Troubleshooting (continued) Kensington Lock Speci cations Replacement part (option/not included in the box) Speci cations (continued) Speci cation of RGB signals in each computer mode of the projector Connectors Dimension drawings (unit: mm) Without terminal cover With terminal cover Speci cations (continued) Speci cation of RGB signals in each computer mode of the projector (continued) MITSUBISHI Projector Contact Information 1 Zusho Baba, Nagaokakyo-City, Kyoto Japan B M ITSUBISHI ELECTRIC CORPORATIO N