To operate projector power ON

 

INPUT SELECT

COMPUTER 1 IN

RS-232C

USB

 

 

REMOTE

AUDIO 1 IN

VIDEO 1

VIDEO 2

 

DIGITAL

 

IN

IN

 

 

 

 

 

ANALOG

 

 

 

 

 

COMPUTER 2 IN

S-VIDEO

MAIN

AUDIO 2 IN

VIDEO

 

O

I

 

 

 

 

AC IN

COMPUTER OUT

L

 

 

AUDIO OUT

 

AUDIO

R

2

,11

 

 

 

 

 

 

 

 

 

 

 

 

3

,9,10

 

 

 

 

FOCUS

TEMP

 

 

 

 

 

 

 

 

 

 

LAMP

5,7

 

 

 

 

 

 

 

 

ZOOM/

 

 

 

 

6

,8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOLUME

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPUTER

VIDEO

 

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

AUTO

MUTE

 

 

 

 

 

 

 

POSITION

 

 

 

 

 

 

 

 

 

 

 

MUTE button

AUTO POSITION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

button

1.Turn on the equipment connected to the projector.

2.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.

3.Turn the projector on by pressing the POWER but- ton.

The light source lamp starts warming up, eventu- ally turning completely on.

When the light source lamp does not light up, wait until the LAMP indicator is turned off, then press the POWER button again.

If the main power switch to the unit is turned off within two minutes of turning off the light source lamp, power will not be applied to the lamp for one minute when the next time the main unit power switch is turned on. When this happens, the indicator lamp will blink for one minute.

indicator

LAMP

POWER

condition

 

 

stand-by

-

red

when light source lamp is on

green

green

light source lamp held off temporarily

-

red

Important:

A darkened image may be seen right after pressing the POWER button due to warming up of this pro- jector. While warming up, no other commands can be accepted.

When the lamp indicator is blinking red, the ser- vice life of the lamp is about to end. Replace the lamp. See pages 23 and 26.

3,9,10

 

 

 

ENGLISH

 

 

 

 

4

 

 

KEYSTONE

 

COMPUTER

VIDEO

ZOOM/

5,7

AUTO POSITION

 

FOCUS

POSITION VOLUME

 

AUTO

 

 

 

button

 

 

 

 

6,8

MENU

 

LASER

 

 

 

RIGHT CLICK

 

 

 

 

ENTER

 

 

 

EXPAND P in P

STILL

STILL button

 

MUTE button

 

 

MUTE

 

The picture might not be of optimum performance in extreme hot or cold conditions. (The projector is not malfunctioning.)

4.Select the desired external input source by using the COMPUTER or VIDEO button.

The projector automatically selects the appropriate signal format. The selected signal format is dis- played on the screen.

When selecting the COMPUTER input, the image may flicker. Press the $ or % button to adjust the image.

For LVP-X400BU only

To view the digital input, select COMPUTER 1 in- put and set the INPUT SELECT switch on the ter- minal board to DIGITAL.

5.Press the ZOOM/FOCUS button to ZOOM. “ZOOM” will appear on the display.

6.Adjust with the + or - button to get an approximate size.

7.Press the ZOOM/FOCUS button to FOCUS. “FO- CUS” will appear on the display.

8.Adjust with the + or - button to get a fine picture.

Focus and zoom adjustment is possible in the normal picture mode only. In PinP or EXPAND mode, the adjustment is prohibited.

´

EN – 13

Page 13
Image 13
Mitsubishi Electronics LVP-X400BU user manual To operate projector power on, Auto Position, Button