Part II: Installation
Connecting a Computer with a VGA Monitor Output
Connecting a Computer
(Figure 1)
1Connect VGA Monitor Out from the com- puter to VGA on the TV back panel using a VGA compatible monitor cable.
TV back panel
| INPUT |
|
|
STB | 1 | 2 | 3 |
|
|
| |
|
|
| 1 |
|
|
| VGAMONITOR CABLE |
|
|
| VIDEO |
|
|
| AUDIO- |
White |
|
| LEFT/ |
|
| (MONO)2 | |
Red |
|
| AUDIO- |
|
| RIGHT | |
|
|
| 2 |
LOOP OUT |
IR EMITTER HOME THEATER
| HIGH RESOLUTION INPUT | |
VGA | COMPONENT 480i /480p | DTV (YPrPb/GRBHV) |
640X480, 60HZ | 1 (YPrPb) 2 (YPrPb) | 480i /480p /1080i |
| Y |
|
| G |
|
| Pr | H |
| R |
|
| Pb | V |
| B | |
|
| AUDIO- |
|
| LEFT/ |
|
| (MONO) |
|
| AUDIO- |
|
| RIGHT |
See Appendix B, page 61, for VGA signal compatability.
2Connect the L (left) and R (right)
audio cables from the computer to VGA AUDIO on the TV back panel. In cases where your computer’s audio output is a single
To utilize the bene ts of a dig tal A/V receiver, connect your computer’s digital audio out, if available, to a digital input on your digital A/V receiver.
CABLE
MONITOR VGA
Computer with VGA Monitor Output. | 1 | |
|
| |
2 | AUDIO |
|
L |
|
2 | VGA OUTPUT |
R |
Figure 1. Connecting a computer with a VGA monitor output.
Connecting the System 4 Home Theater IR Control
(Figure 1)
a Computer and the System 4 Home Theater IR Control
1
2
3
4
Connect the IR emitter to IR EMITTER HOME THEATER on the TV back panel. Place the IR emitter cable under or along the side of the A/V device. Place the IR lens directly in front of the A/V device’s infrared signal receiver. Infra- red signal receivers are usually behind the front translucent panel of the device. Place unused transmitters in an
For permanent installation of the IR emitter cable, use the included adhesive tape to secure the bottom of the emitter to the anchoring object of your choice.
TV back panel
| INPUT |
|
| OUTPUT |
STB | 1 | 2 | 3 | MONITOR PIP |
|
|
|
| |
|
|
|
| VIDEO |
|
|
|
| AUDIO- |
|
|
|
| LEFT/ |
|
|
|
| (MONO) |
|
|
|
| AUDIO- |
|
|
|
| RIGHT |
| LOOP OUT |
IR EMITTER HOME THEATER
| HIGH RESOLUTION INPUT | |
VGA | COMPONENT 480i /480p | DTV (YPrPb/GRBHV) |
640X480, 60HZ | 1 (YPrPb) 2 (YPrPb) | 480i /480p /1080i |
| Y |
|
| G |
|
| Pr | H |
| R | |
|
| |
| Pb | V |
| B | |
|
| AUDIO- |
|
| LEFT/ |
|
| (MONO) |
|
| AUDIO- |
|
| RIGHT |
Connecting
| 1 |
Other A/V Device | A/V Receiver |
See page 53 for details on using the
TV’s IR emitter to control a Mitsubishi
A/V receiver. | Figure 2. Connecting the System 4 Home Theater IR |
| Control. |
22