Mitsubishi Electronics S490, X490, X500 user manual User memory for signal setting, English, Signal

HOLD

USER MEMORIZE

MEMORY CALL HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT

ANAMORPHIC ....	Select ON when playing DVD discs containing data of letterboxed images.
LANGUAGE	Use to select the language used in the menus. (	/ English / Español / Deutsch / Français / Italiano
	/ )
RESET ALL	Use to reset the MENU settings (except LANGUAGE).

•When the LANGUAGE in FEATURE menu is set to English and NTSC video format is selected, the brightness is decreased 15 points by set-up cancel function for U.S. (The indicated value is not changed.) The image becomes darker, but this is not a failure of the projector.

ENGLISH

4 SIGNAL
MEMORY CALL	Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION	Use to adjust the horizontal position of the image.
VERT. POSITION	Use to adjust the vertical position of the image.
FINE SYNC	Use to synchronize the projector with PC input signals so that
	the image is not blurred.
TRACKING	Use to avoid image noise such as wide stripes.
COMPUTER INPUT	The unit adjusts itself automatically when connected to a DVD
	player with a component video output (Y, CB, CR). In the case ( Y,
	PB, PR). In the case the projector is connected to equipment that
	includes RGB output terminal, adjust to RGB mode.
HOLD	Adjusts the image when flagging occurs near the top of the
	screen.

SIGNAL

A

U

R G B

R G B

opt.

XGA60

AUTO

0

0

0

0

RGB

AUTO

DELETE DEFAULT

5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH .......... If you use something similar, the brighter colors of the projected
	SIGNAL-USER
image may become blurred. In this case, adjust CLAMP POSITION
	CLAMP POSITION	0
or CLAMP WIDTH.
	CLAMP WIDTH	0
HORIZ.PIXELS .... Use to adjust the width of the image. The image size grows wider as
	HORIZ. PIXELS	0
the number increases. (Adjust to the horizontal pixels of the input
	VERT. LINES	0
signal for normal setting.)
	VERT. SYNC.	AUTO
VERT.LINES ....... Use to adjust the height of the image. The image size grows higher
	SHUTTER(U)	0
as the number increases. (Adjust to the vertical lines of the input
	SHUTTER(L)	0
signal for normal setting.)
	SHUTTER(LS)	0
VERT.SYNC. ........ Use to adjust the image when its motion does not run smoothly.
Select AUTO for normal setting.	SHUTTER(RS)	0
SHUTTER(U) ....... Use to adjust the image when the noise etc. appears on top part of
image.
SHUTTER(L) ....... Use to adjust the image when the noise etc. appears on bottom part of image.
SHUTTER(LS) ..... Use to adjust the image when the noise etc. appears on left side of image.
SHUTTER(RS) ..... Use to adjust the image when the noise etc. appears on right side of image.

User memory for signal setting

This projector can memorize the maximum of 2 signal menu settings.

Memorizing the setting

1.Select MEMORIZE in the SIGNAL menu, and press the ENTER button.

2.Press the $or %button to select the memory which you wish to record (USER 1 or USER 2).

3.Press the ENTER button.

•Any buttons are ineffective about 3 seconds of recording setting. Wait for recording to have been completed before operating the buttons.

Initialite the setting which has been changed (Default)

Select RESET in the SIGNAL menu, and press the ENTER button.

Select the user setting

Select MEMORY CALL in SIGNAL menu, and press the $or %button to select the memory (USER 1 or USER 2).

Reset the recorded setting

1.Select DELETE in the SIGNAL menu, and press the ENTER button.

2.Press the $or %button to select the memory which you wish to reset (USER 1 or USER 2).

3.Press the ENTER button.

The recorded setting will be reset.

•Any buttons are ineffective about 3 seconds of resetting the recorded setting. Wait for resetting to have been completed before operating the buttons.

EN – 17