INSTALLATION INSTRUCTIONS
Included in bidet trim kit
DISCHARGE TUBE | SPRAY NOZZLE |
| RUBBER WASHER |
| RUBBER WASHER |
| METAL WASHER |
| MOUNTING NUT |
| 3/8" x 3/8" x 22" |
| SUPPLY TUBE |
Seat
Drain hole
Bottom gasket
Drain body
Slip joint nut (not included) Slip joint washer (not included)
Floor drain (not included)
INSTALLATION OF SPRAY ASSEMBLY
1.Install rubber washer over threaded nipple of spray nozzle assembly and place down through smaller hole in bidet bowl. From below install metal washer, metal washer and mounting nut and tighten.
2.Attach supply tube to spray assembly nipple and to discharge tube as shown.
|
| Cold Side |
| Hot Side | COL |
|
| D S IDE |
|
| Supply Hose |
|
| Supply Tube |
|
| (not supplied) |
Supply Stop |
| "Tee" Connection |
|
| |
(not supplied) | Inlet Tube |
|
|
| |
| Supply Tube |
|
TO INSTALL WASTE ASSEMBLY:
1.Thoroughly clean around drain opening on bidet drain hole. Apply a 1/4" bead of plumber's putty (not furnished) around the drain opening.
2.Apply pipe joint compound or Teflon tape (not furnished) to top threaded end of drain body. Slip drain body up through the drain opening and screw seat on the drain body.
3.Position the drain body with pivot rod opening extending rearward and tighten mounting nut until the drain body is snug. Wipe excess plumber's putty from seat area. Apply pipe joint compound or Teflon tape to top threaded end of tailpipe and screw into drain body. Tighten firmly by hand.
4.Position the drain plug in either of the following ways:
A.VANDALPROOF - This design is to prevent unauthorized removal of the drain plug. Unscrew the pivot nut and remove the pivot rod. Inside the drain body, position the pivot rod through the drain plug hole as shown in the illustration. Screw the pivot nut back on the drain body. DO NOT OVERTIGHTEN.
B.EASY REMOVAL - This design is for quick removal of drain plug for cleaning. Just drop in the drain plug as shown in the illustration.
CONNECTING SUPPLY VALVES TO DIVERTER VALVE AND WATER SUPPLIES:
1.Slide "TEE" onto inlet tube and tighten compression nut. NOTE: Check to insure ferrule and nut are in place before installing tee onto inlet tube. Thread one end of each supply hose onto a supply valve, the other end is threaded to the "TEE" connection inlet. Supply hoses can be crossed or looped for ease of assembly. NOTE: Remove "COLD SIDE" tape before making connection.
2.Connect supply tubes (not supplied) to inlet ports. Finish tightening supply valve mounting hardware.
A | B |
Pivot Rod | Pivot Rod |
VANDAL PROOF | EASY REMOVAL |
WARRANTY | CONSUMER INFORMATION |
|
|
Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period” for homeowners), that this faucet will be leak and
IfthisfaucetshouldeverdevelopaleakordripduringtheWarranty Period, Moen will FREE OF CHARGE provide the parts necessary to put the faucet back in good working condition and will replace FREE OF CHARGE, any part or finish that proves defective in material and manufacturing workmanship, under normal installation, use and service. Replacement parts may be obtained by calling
This warranty is extensive in that it covers replacement of all defective parts and finishes. However, damage due to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents, whether performed by a contractor, service company, or yourself, are excluded from this warranty. Moen will not be responsible for labor charges and/or damage incurred in installation,repairorreplacement,norforanyindirect,incidentalorconsequentialdamages,losses,injuryor costs of any nature relating to this faucet. Except as provided by law,thiswarrantyisinlieuofandexcludes all other warranties, conditions and guarantees, whether expressed or implied, statutory or otherwise, includingwithoutrestrictionthoseofmerchantabilityoroffitnessforuse.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Thiswarranty gives you specificlegal rightsandyoumayalsohaveotherrightswhichvaryfromstatetostate,provincetoprovince,nationtonation. Moen will advise you of the procedure to follow in making warranty claims. Simply write to Moen Incorporated using the address below.Explainthedefectandincludeproofofpurchaseandyourname,address,areacode and telephone number.
Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed to stand in contact with the brass. The amount of lead contributed by any faucet is highest when the faucet is new. The following steps may reduce potential exposure to lead from faucets and other parts of the plumbing system:
•Always run the water for a few seconds prior to use for drinking or cooking
•Use only cold water for drinking or cooking
•If you wish to flush the entire plumbing system of water that has been standing in the pipes or other fittings, run the cold water until the temperature of the water drops, indicating water coming from the outside main
•If you are concerned about lead in your water, have your water tested by a certified laboratory in your area
HELPLINE:
1 (800)
In the U.S. call our toll free Helpline number, for answers to any product installation, or warranty questions.
In Canada:
Toronto:
Rest of Canada:
In Mexico:
(84)
3 | Moen Incorporated • 25300 Al Moen Drive • North Olmsted, OH | INS271 |
