WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.

If your home’s

wiring system is not a three-wire grounded system, do not use this electric starter under any conditions.

If your home electrical system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in the Tecumseh Engines manual packed separately with your snow thrower. Read instructions carefully.

Starting The Engine

1.Attach spark plug wire to spark plug. Make certain the metal loop on the end of the spark plug wire (inside the rubber boot) is fastened securely over the metal tip on the spark plug.

2.Make certain both the auger control and drive control are in the disengaged (released) position.

3.Move throttle control up to FAST position. Insert ignition key into slot. Make sure it snaps into place. Do not attempt to turn the key.

NOTE: The engine cannot start unless the key is inserted into ignition switch.

Electric Starter

1.Determine that your home’s wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain.

WARNING: The optional electric starter is equipped with a grounded three-wire power cord and plug, and is designed to op- erate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter.

If you have a grounded three-prong receptacle, proceed as follows:

1.Plug the extension cord into the outlet located on the engine’s surface. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area.

2.Rotate choke control to FULL choke position (for a cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

3.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

4.Push starter button to start engine.

5.Once the engine starts, release starter button.

6.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to FULL and then slowly into the OFF position again.

7.When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower.

Recoil Starter

1.Rotate choke control to FULL choke position (cold engine start).

NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL.

2.Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing.

NOTE: DO NOT use primer to restart a warm engine after a short shutdown.

NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit.

3.Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil.

4.Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil.

5.As the engine warms, slowly rotate the choke control to the OFF position. If the engine falters, quickly rotate the choke control back to the FULL position and then slowly into the OFF position again.

NOTE: Allow the engine to warm up for a few minutes after starting. The engine will not develop full power until it reaches operating temperatures.

Stopping The Engine

Run engine for a few minutes before stopping to help dry off any moisture on the engine.

1.Move throttle control to STOP position.

2.Remove the ignition key and store in a safe place.

3.Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times.

10

Page 10
Image 10
MTD 769-01275D warranty Gas & Oil Fill-Up, Stopping The Engine, If your home’s, Electric Starter, Recoil Starter

769-01275D specifications

The MTD 769-01275D is an outstanding model in the realm of outdoor power equipment, particularly recognized for its performance and reliability in lawn care and maintenance. Engineered by MTD Products, a company with a rich heritage in manufacturing outdoor power tools, this model combines advanced technologies with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the main features of the MTD 769-01275D is its powerful engine. Designed to deliver efficient operation, the engine provides ample torque and speed, enabling the machine to tackle various types of terrain and grass densities. Its robust construction promises durability, ensuring that the equipment can withstand rigorous use throughout the season.

The MTD 769-01275D is equipped with an innovative cutting system that enhances its performance. With adjustable cutting heights, users can customize the mower to achieve the desired grass length, whether for a well-manicured lawn or a natural look. This versatility is further complemented by sharp, high-quality blades that promote clean cuts, resulting in healthier grass growth and an aesthetically pleasing yard.

A standout characteristic of the MTD 769-01275D is its ergonomic design. The handle is designed for comfort and ease of use, reducing fatigue during extended periods of operation. Additionally, the intuitive controls allow users to navigate various settings without complications, making the mowing experience more enjoyable and efficient.

Technologically, the MTD 769-01275D incorporates features such as easy-start mechanisms, and some models may include electric start options, allowing for quick and hassle-free ignition. Fuel efficiency is another significant aspect, with the engine designed to consume less fuel while providing maximum power.

Another commendable feature is the design of the deck. The wide cutting deck allows for more extensive cutting swath, significantly reducing the time spent mowing. It is also designed to be lightweight, making it easier to maneuver around obstacles in the yard.

Overall, the MTD 769-01275D stands out for its combination of power, convenience, and innovative features. Whether for residential use or professional landscaping, it represents an excellent investment for those looking to maintain their outdoor spaces effectively. Its blend of efficiency, durability, and user-centric design makes it a desirable option among outdoor power equipment.