MP2 MASONRY SAW — PRE-SETUP (GASOLINE ENGINE)

Dry Cutting Setup (Gasoline Only)

CAUTION - Dry Cutting

ALWAYS use the water feed system unless special dry cut blades are being used. If dry cutting is required disconnect water pump.

To disconnect the mechanical water pump from the drive V-belts for Dry Cutting, perform the following:

1.Loosen the 2 hex head cap screws (Figure 14) that secure the pump mount bracket.

2.Pull the pump handle upward to disengage the pump.

3.Tighten the 2 hex head cap screws that secure the pump mount bracket.

Figure 14. Pump Disengage

Before Starting

1.Read safety instructions at the beginning of manual.

2.Clean the saw, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner.

3.Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

4.Check carburetor for external dirt and dust. Clean with dry compressed air.

5.Check fastening nuts and bolts for tightness.

Engine Oil Check

1.To check the engine oil level, place the saw on a secure level surface with the engine stopped.

2.Remove the filler dipstick from the engine oil filler hole (Figure 15) and wipe clean.

Figure 15. Engine Oil Dipstick (Removal)

3.Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

4. If the oil level is low

UPPER

 

(Figure 16), fill to the edge

 

of the oil filler hole with the

 

recommended oil type

 

(Table 5). Maximum oil capacityis1.16quarts(1.1

liters)

 

 

 

LOWER

 

 

 

 

Figure 16. Engine Oil Dipstick (Oil Level)

 

 

 

 

 

 

TABLE 5. OIL TYPE

 

 

 

 

 

 

Season

 

Temperature

 

Oil Type

 

 

 

 

 

Summer

 

25°C or Higher

 

SAE 10W-30

 

 

 

 

 

Spring/Fall

 

25°C~10°C

 

SAE 10W-30/20

 

 

 

 

 

Winter

 

0°C or Lower

 

SAE 10W-10

 

 

 

 

 

CAUTION - Explosive Fuel

Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. DO NOT attempt to refuel the pump if the engine is hot! or running.

Fuel Check

1.Remove the gasoline cap located on top of fuel tank.

2.Visually inspect to see if the fuel level is low. If fuel is low, replenish with unleaded fuel.

3.When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel.Wipe up any spilled fuel immediately!

PAGE 24 — MQ MP2 MASONRY SAW — OPERATION MANUAL — REV. #2 (03/12/13)

Page 23 Page 25
Page 24
Image 24
Multiquip MP2050E1 MP2 Masonry SAW PRE-SETUP Gasoline Engine, Dry Cutting Setup Gasoline Only, Before Starting, Fuel Check
Page 23 Page 25

MP2090HP, MP2050E3, MP2050E1 specifications

The Multiquip MP2050E1, MP2050E3, and MP2090HP are powerful and versatile electric-powered concrete and masonry saws designed for a variety of cutting applications. Built with durability and performance in mind, these models cater to the needs of professional contractors, offering exceptional efficiency and precision in both residential and commercial projects.

The MP2050E1 features a high-torque electric motor that ensures reliable operation and consistent cutting performance. It comes equipped with a 20-inch blade capacity, allowing users to tackle medium to large-sized jobs with ease. The saw is designed with an ergonomic handle and adjustable height for optimal user comfort during extended use. Additionally, the MP2050E1 boasts a compact design, making it easy to transport and maneuver around job sites.

On the other hand, the MP2050E3 is an upgraded version that incorporates advanced features while maintaining the same blade capacity as its predecessor. This model includes a three-phase motor, which enhances power efficiency and increases the saw's longevity. The MP2050E3 is engineered with a robust chassis for increased stability during operation, and it also offers improved dust management capabilities to keep the work area clean and safe.

The Multiquip MP2090HP stands out with its higher horsepower motor, optimizing productivity for heavy-duty cutting tasks. This model supports a larger blade size of up to 30 inches, making it ideal for cutting thicker materials. The MP2090HP is equipped with a sophisticated water control system that ensures consistent cooling of the blade, preventing overheating and prolonging blade life. Its heavy-duty construction is designed to withstand the rigors of demanding job sites, offering maximum reliability.

All three models utilize cutting-edge technology, including adjustable cutting depth settings, which allow operators to customize their cutting depth for precision and versatility. They also feature high-performance bearings that provide smooth blade rotation, enhancing overall cutting efficiency.

In summary, the Multiquip MP2050E1, MP2050E3, and MP2090HP are exemplary tools for professionals in the concrete and masonry industry. Each model boasts unique features tailored to meet varying job requirements, while their advanced technologies ensure high performance, safety, and ease of use. Whether tackling small renovations or large construction projects, these saws provide the reliability and power needed to achieve exceptional results.
Top Page Image Contents