Multiquip operation manual MT-62HS Operation and Safety Decals

NPA-963 J

MT-62HS — OPERATION AND SAFETY DECALS

P/N 920100240

CAUTION

ATTENZIONE

ATENÇAÕ

PRECAUCION

*Read operator’s manual carefully before use.

*Libre le manual attentivement avant utillsation.

*Bitte lesen Sie vor inbetriebnahme der Maschine de Bedienungsanleitung sogfältig durch.

*Prima dell’ uso leggere attentamente il manuale.

*Lee com atenÇão o manual de instruÇões antes de usar.

*Leer detenidamente el mamual de instrucciones antes de usar la maquina.

NPA-769 J

P/N NPA-769

	Oil
	öl
	I’ huile
	SAE30
NPA-961 E	7~9 cc

P/N 920209610

5 MM (3/16”)

PROPER SPONGE INSTALLATION

NPA 398 J

P/N 920203980

NPA-910 J

P/N 920209100

CLEANING ELEMENT:

Remove the element from the pre-cleaner Clean the element with solvent

Apply SAE30 motor oil with 7~9 cc, and squeeze out excess oil before re-installing.

P/N NPA-963

NOTICE

CLEAN THE ELEMENT WITH KEROSENE WHEN DIRTY. AFTER THE CLEANING, LUBRICATE IT MIXED OIL (KEROSENE 2~4: ENGINE OIL 1), SQUEEZE OUT THE OIL, AND REPLACE IT. AND CLEAN IT MORE

OFTEN WHEN OPERATING IN DUSTY CONDITIONS. NP-831 J

P/N 920108310

DO NOT ALLOW WATER

TO ENTER FUEL AND OIL TANKS

NP-599 J

P/N 920205990

To start, switch must be in the “ON” position

READ OWNER’S SERVICE MANUAL BEFORE OPERATING OR SERVICING THIS MACHINE.

ALWAYS KEEP UNAUTHORIZED, INEXPERIENCED, UNTRAINED PEOPLE AWAY FROM THIS MACHINE.

MAKE SURE ALL SAFETY DEVICES ARE OPERATIONAL BEFORE THIS MACHINE IS STARTED. MAKE SURE ENGINE IS TURNED OFF AND SPARK PLUG WIRE DISCONNECTED BEFORE SERVICING THE MACHINE OR COMING IN CONTACT WITH ANY MOVING PART. IF EQUIPMENT IS POWERED BY AN ELECTRIC MOTOR DISCONNECT ELECTRICAL PLUG.

SAE 10W-30

Motor Oil

NPA-195 J

P/N 920201950

NPA 293

P/N 920202930

When you stop the engine, be sure to close the fuel cock

NPA-399 J

P/N 920203990

NEVER LEAVE MACHINE UNATTENDED WHEN OPERATING. ALWAYS STOP ENGINE AND ALLOW ENGINE TO COOL BEFORE ADDING FUEL OR OIL.

NPA-329 J

P/N 920203290

NAMEPLATE

3800 ~ 4000 RPM	CONTACT MULTIQUIP
NPA-984 J
P/N 920209840	SERVICE DEPT.

CAUTION

	1.	Check that all bolts are tight.
	2.	Before operation, check oil level at the sight gauge located
		on the operator’s side of the oil tank. Fill the oil tank to the
		“H” level using only outboard (2-stroke) oil.
P/N 920205810	3.	Fill the fuel tank. Use only regular unleaded gasoline.
	4. To start the engine: Turn the ignition switch to the “on”
		position. Open the fuel-cock located under the fuel tank.
		Close the choke lever located on the carburetor and pull
		starter rope. When engine starts, open choke fully.
	5.	Should the engine become difficult to start, open the drain

NPA-581 J

cock located on the lower side of the crankcase and discharge any excess fuel by cranking the engine 2 or 3 times.

6.Allow the engine to warm up for 4 to 5 minutes before operation.

7.To begin operation, move the throttle lever quickly from the “start” to the “run” or “on” position.

8.Remember to close the engine drain-cock after starting to ensure proper operation.

9.When operation is complete, stop the engine by turning the ignition switch to the “off” position.

10.Note: Transport the machine with the fuel-cock in the “off” position only.

PAGE 10 — MT-62HS — PARTS & OPERATION MANUAL — REV. #2 (12/15/03)