Manuals / Multiquip / Kitchen Appliance / Trash Compactor

Multiquip MVH-702DRSC manual Before START-UP, Settingthe Operational Channel

Models: MVH-702DRSC

1 58
Download 58 pages 4.15 Kb
Page 20
Image 20

MVH-702DRSC — BEFORE START-UP

BEFORE START-UP

1.Read this manual carefully and understand all functions of the machine before start-up.

2.The engine is located on front side of the machine and the aluminum oil tank is on the rear.

3.The operator should always keep a distance of 2 meters away from the machine.

4.The operator should always make sure that the machine will move in the opposite direction (away from him) when the machine is started.

5.In infra-red remote control operation, the farther the machine moves, the narrower the control area.

6.If the transmitter fails and during emergencies, pull the emergency stop lever (Figure 8) continuously until the machine completely stops.

Emergency

Stop Lever

Figure 8. Location of Emergency Stop Lever

Remote Control operation is not available in the following cases. Vibration stops automatically.

Operator stands within approximately 3 feet (1 m) of the machine.

Operator stands approximately 60 feet (18 m) or farther from the machine (approximately 40 feet (12 m) when far from the direct rays of the sun). Note that these distances may vary .

Operator stops sending control signals for more than one second.

The engine is overloaded. In the engine temperature increases, the vibration will automatically stop.

The engine stops automatically in the following cases.

Engine oil level is low.

Control unit fails to receive the operational signal for more than 30 seconds.

During engine or hydraulic oil warm-up, direct the transmitter to the body receiver to receive the operational signal. Operation starts only after the main switch of the transmitter is switched on.

SETTINGTHE OPERATIONAL CHANNEL

In cases where several machines operate in the same area, each machine should be transmitting in a different infra-red channel.Ten different channels can be set (0 to 9).See Table 2. To set the operational channel of a machine, do the following.

1.On the body of the machine, remove the receiver channel plug. See Figure 9. Using a screwdriver, set the channel number desired.

2.On the transmitter, remove the channel plug. See Figure 9. Using a screwdriver, set the channel number to the same one as the receiver (set in step 1).

Remove plug and adjust

MACHINE

Remove plug and adjust

TRANSMITTER

Figure 9. Setting Channels

Table 2. Channel Number Settings

TRANSMITTER

RECEIVER

 

 

0

0

 

 

1

1

 

 

2

2

 

 

3

3

 

 

4

4

 

 

5

5

 

 

6

6

 

 

7

7

 

 

8

8

 

 

9

9

 

 

PAGE 20 — MQ-MIKASA MVH-702DRSC COMPACTOR — PARTS & OPERATION MANUAL — REV. #1 (12/17/03)

Page 19 Page 21
Page 20
Image 20
Multiquip MVH-702DRSC manual Before START-UP, Settingthe Operational Channel
Page 19 Page 21

MVH-702DRSC specifications

The Multiquip MVH-702DRSC is a state-of-the-art, reversible plate compactor that has been designed for maximum performance and efficiency in soil and asphalt compaction. Renowned for its durability and user-friendly features, the MVH-702DRSC is an ideal choice for a wide variety of construction and landscaping applications.

One of the standout features of the MVH-702DRSC is its powerful 4.5 hp engine, ensuring optimal performance in tough working conditions. The engine is not only reliable, but it also provides excellent fuel efficiency, allowing for extended operation without the need for frequent refueling. The compact design of the MVH-702DRSC enables it to easily navigate tighter job sites, making it an exceptional choice for residential and commercial projects alike.

Another remarkable characteristic of this plate compactor is its advanced vibration technology. With a maximum centrifugal force of 3,300 pounds, the MVH-702DRSC ensures efficient compaction of granular and cohesive soils. It features a wide base plate that is specifically designed to provide a high degree of stability and effective material displacement, which results in a well-compacted surface. The ability to reverse also allows operators to perform tasks quickly and effectively, eliminating the need to reposition the machine for optimal operation.

User comfort and control are prioritized in the design of the MVH-702DRSC. The ergonomic handle is adjustable and designed to reduce operator fatigue, allowing for extended periods of use without discomfort. The machine also incorporates a sophisticated splash guard, which helps to keep the engine and components clean, an important aspect that contributes to longevity and performance.

Moreover, the MVH-702DRSC is equipped with a protective frame that safeguards critical components during operation, minimizing maintenance requirements over time. The compact and robust design assures ease of transport, as it can fit in small trailers or truck beds, enabling contractors to easily move it between job sites.

In conclusion, the Multiquip MVH-702DRSC is a high-performing, versatile reversible plate compactor that combines power, efficiency, and user-friendly features. From its durable construction to its advanced vibration technology, it is designed to meet the rigorous demands of the construction industry while ensuring comfort and ease of use for operators. Ideal for compacting soil and asphalt, the MVH-702DRSC is a reliable choice for professionals seeking a robust compaction solution.