ST-2005 SERIES SUB. PUMP— CONTROL BOX INSTALLATION

Connecting AC Power to the Control Box

1.The AC power cord (input) should have three wires. Each wire is color coded. The colors are WHITE, BLACK and

GREEN.

2.Remove the AC input connector housing from the control box, then route the power cord through the cable gland on the control box.

3.Connect the AC power cord to the contactor as shown in Figure 7 and Table 6.

TABLE 6. AC INPUT POWER

CONNECTIONS TO CONTACTORS

CABLE WIRE COLOR

CONTACTOR

 

 

BLACK

L1

 

 

WHITE

L2

2.Remove the pump AC input connector housing from the control box, then route the power cord through the cable gland on the control box.

3.Connect the pump power cord to the contactor as shown in Figure 7 and Table 7.

TABLE 7. AC OUTPUT POWER

CONNECTIONS TO PUMP

CABLE WIRE COLOR

CONTACTOR

 

 

BLACK

T1

 

 

WHITE

T2

 

 

GREEN

GROUND

 

 

GREEN

GROUND

3. Tighten the connector housing to ensure a tight fit between

the power cord and the connector body. This will prevent

NOTE

Turning On The Pump

Electrical connections to the power source should only be performed by a licensed electrician or qualified

personnel.

the cable from pulling out of the terminal block and also

prevent moisture from entering the control box.

Itisrecommendedthatthepowerbeing supplied to the control box ALWAYS

NOTE be connected to a circuit breaker or a quick disconnect switch. This safetyfeatureallowsforquickremoval of power from the control box in the event of an emergency.

4.Connect the other end of the AC power cord to the voltage source. Remember to provide a means of disconnecting the power from the control box (circuit breaker or quick disconnect switch). Also make sure to provide a good earth ground to the control box.

Connecting AC Power to the Pump

1.AC power is transferred to the pump via a contactor. The coil of the contactor is energized or de-energized by the opening and closing of the float switch contacts.The power cord should have three wires. Each wire is color coded. The colors are WHITE, BLACK and GREEN.

1.If all of the pump's electrical requirements have been met, placethecircuitbreakerorpowerON/OFFswitchintheON position.

2.The CB3 control box has an operation switch located on thefrontcover.Thisswitchhas3positions, AUTO,MANUAL and OFF. The AUTO position allows the pump to run in an un-attended mode.The MANUAL position will let the pump run without the float switches controlling the pump. When in the manual mode be careful not to let the pump run dry. Severe damage to the pump may occur if it is allowed to run dry.NEVER let the pump run dry.

3.Place the operation switch in the AUTO position. The AC power indicator lamp should be lit (ON).

4.Wait a few seconds and water should begin to flow from the discharge hose.

5.If water is not flowing from the discharge hose or not flowing freely after a few minutes, remove the power from the pump and check the system for leaks.

6.To stop the pump from pumping, place the operation switch in the OFF position.

ST-2005 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV. #3 (09/21/04) — PAGE 17

Page 17
Image 17
Multiquip ST-2005 manual Connecting AC Power to the Control Box, Personnel, Connecting AC Power to the Pump

ST-2005 specifications

The Multiquip ST-2005 is a compact yet powerful generator that stands out in the market for its reliability and efficiency, making it a popular choice for construction sites, outdoor events, and emergency power needs. Engineered to deliver dependable electricity, it is equipped with advanced features and technologies that cater to both professional and personal use.

One of the standout features of the ST-2005 is its robust 4-stroke engine, which provides an impressive output of 2000 watts. This engine is designed with fuel efficiency in mind, allowing users to run their electrical tools and devices for extended periods without frequent refueling. The generator’s fuel tank has a capacity of 1.8 gallons, providing an operating time of up to 10 hours on a quarter load, a significant advantage for users requiring consistent power throughout the day.

Portability is another key characteristic of the Multiquip ST-2005. Weighing in at just around 50 pounds, this generator features a compact design that includes a sturdy frame and integrated wheels, allowing for easy transportation to various job sites or events. The foldable handle adds to its portability, making it convenient to store when not in use.

The ST-2005 incorporates state-of-the-art technologies that enhance its performance and usability. This includes an integrated inverter system that ensures clean and stable power output, making it suitable for sensitive electronic devices such as laptops and smartphones. Along with this, the generator features a low oil shutdown mechanism, which automatically turns off the engine if the oil level drops below a safe threshold, thereby protecting the engine from damage.

User-friendly control panels are another hallmark of the Multiquip ST-2005. The generator comes equipped with multiple output outlets, including 120V and 12V options, allowing users to connect a variety of devices simultaneously. Additionally, an easy-to-read watt meter provides real-time information on power usage, ensuring that users can efficiently manage their energy consumption.

In conclusion, the Multiquip ST-2005 is designed for durability, performance, and ease of use. With its powerful engine, portability, advanced inverter technology, and user-friendly features, it serves as an invaluable tool for anyone needing reliable power on the go, making it a worthy investment for both professionals and home users alike.