Multitech MT5600BL, MT5600BA guide

ASYNC, NORM? Normal asynchronous transmission using the

Chapter 3 - Using the Front Panel

COMMAND MODE OPTIONS. The following screens are used to configure result code responses.

ENABLE/DISABLE RESPONSE. Use the Æ and Enter buttons to enable or disable the sending of result codes to the computer. Same as the Q0 and Q1 commands.

VERBOSE/TERSE RESPONSE. Use the Æ and Enter buttons to select verbose or terse result codes. Same as the V0 and V1 commands.

ENABLE/DISABLE CMD MODE. Use the Æ and Enter buttons to enable or disable the modem’s ability to accept AT commands

.

SYNC/ASYNC OPTIONS. Use the Æ and Enter buttons to select the method of data transmission.

ASYNC, NORM? Normal asynchronous transmission using the

AT command set.

ASYNC, V.25bis? Asynchronous transmission using the V.25bis command set.

SYNC, NORM? Normal synchronous transmission using any command set.

V.25bis HDLC NRZ? V.25bis synchronous transmission using

NRZ encoding.

V.25bis HDLC NRZI? V.25bis synchronous transmission using

NRZI encoding.

V.25bis BISYNC? V.25bis bisynchronous transmission.

RESET FACTORY DEFAULTS. Use the Æ and Enter buttons to reset Profile 0 and the modem’s active configuration to the factory defaults. Same as the AT&F&W command string.

CONNECT RATE OPTIONS. Use the Æ and Enter buttons to change the modem’s serial port and data transmission speeds.

SERIAL BAUD RATE. Use the Æ and Enter buttons to select the modem’s serial port speed. The valid range is 1200 to 115200 bps. Same as the $SB commands.

MODEM SPEED. Use the Æ and Enter buttons to select the modulation protocol to use in originating or answering a connection. This also selects the maximum transmission speed at which the modem can operate. Same as the +MS=[mod] command.

Multi-Tech Systems, Inc. MT5600BA/BL Series User Guide (S000276E)	24

Image 24

Multitech MT5600BL, MT5600BA manual ASYNC, NORM? Normal asynchronous transmission using the

Contents

MT5600BA/BL Series Data/Fax Modem User GuideMT5600BA-V.92 MT5600BA-V.90 MT5600BL-V.90 MultiModemII User Guide Record of RevisionsTrademarks Patents Table of Contents Table of ContentsMultiModemII User Guide None of the Indicators Light Chapter 1 - Description and Features About AT CommandsFeatures Product Description Safety Warnings Connect theTwo-Wire Leased Line Step 1 - Connect the Modem to Your SystemConnect the Modem to Your PC Connect the Modem to the Telephone Line Dialup Connection Connect the Four-Wire Leased Line Connect the Modem to the AC Power OutletPower-On Test Connect the Phone to the Modem Optional Step 2 - Install the Modem Driver Installing the Modem Driver for Windows 98/Me/2000 XPInstalling the Modem Driver for Windows NT Removing an Old Modem Driver Step 3 - Setting Your Country or Region Code Using the LCD PanelUsing the Global Wizard MT5600BA-V.92 Only Step 4 - Install PhoneTools Using AT CommandsHow to Change the Country/Region Code How to Verify the Code Chapter 3 - Using the Front Panel Modem ConfigurationLED Indicators Liquid Crystal Display LCD Option SelectionMenu Structure Menu Overview TrunksLimbs Branches Status Trunk Limbs Twigs Basic Options Trunk LimbsBranches Twigs Basic Options Trunk, continued Continued from previous page Advanced Options Trunk Advanced Options Trunk, continued Remote Configuration Options Trunk Diagnostic Options TrunkLimb Phone Number Memory Options Trunk Caller ID Options Trunk Menu Options Status Basic Options ASYNC, NORM? Normal asynchronous transmission using the Advanced Options VIEW S-REGISTER SETTINGS. Use the Æ, È, ÇÅ, and Enter buttons to select the number of the S-register whose value you want displayed. To scroll through a list of digits, press the ÇÅ and È buttons. To go to the next position, press the Æ button. To back up or to exit without saving, press the Æ button several times. To display the value, press the Enter button. Same as the Sr? command Remote Configuration Options Diagnostic OptionsPhone Number Memory Options Caller ID Options Two-Wire Setup Chapter 4 - Leased Line Operation Four-Wire Setup Dial Backup and Leased-Line Restoral Dial Backup and Leased Line Restoral Setup 10. Press the Æ button to go to the next digit in the number Chapter 5 - Remote Configuration Basic ProcedureSetup Changing the Remote Configuration Password Changing the Remote Escape Character Setup Procedures AT Command MethodChapter 6 - Callback Security Turning Callback Security On and Off Assigning Callback Passwords AT Command MethodFront Panel Method Assigning Callback Phone Numbers Front Panel Method Calling Procedure Callback Security Commands Command #DBn Callback Enable/DisableCommand #CBN y= - x Store Callback Number Command #CBP y= x Store Callback Password LocationPasswordPhone Number Callback Assignments Form Chapter 7 - Troubleshooting None of the Indicators Light The Modem Does Not Respond to Commands The Modem Cannot Connect When Dialing The Modem Disconnects While Online The Modem Cannot Connect When Answering File Transfer Is Slower Than It Should BeData Is Being Lost There Are Garbage Characters on the Monitor The Modem Doesn’t Work with Caller IDFax and Data Software Can’t Run at the Same Time Appendix A - Regulatory Compliance FCC Part 68 Telecom Fax Branding Statement Canadian Limitations Notice EMC, Safety, and R&TTE Directive Compliance International Modem RestrictionsNew Zealand Telecom Warning Notice South African Notice Appendix B - Technical Specifications loop Upgrade Overview Appendix D - Upgrading the FirmwareIntroduction Step 1 - Identify the Modem Firmware Step 3 - Download the Upgrade File Step 4 - Extract the Upgrade FilesStep 2 - Identify the Current Firmware Version Step 6 - Upgrade the Modem’s Firmware Step 7 - Restore Your ParametersStep 5 - Clear Your Stored Paramenters Appendix E - Installing a Modem Under Linux Using the Terminal Program Minicom to Verify OperationStandard Linux Serial Port Definitions Installation Using the Modem to Call the Internet Calling the ISPAnswering Calls 3. Select Dialup Configuration Tool Appendix F - Pin Descriptions RS-232 Pin Descriptions RS-232 Cable Pinouts Appendix F - Pin Descriptions Leased Line Pinouts DTE Mini-DIN 8-pin connectorDCE DB-25 connector HSKi CTS HSKo RTS Index