5. SPEAKERS A & SPEAKERS B

The NAD C270 is equipped with two sets of speaker connectors wired in parallel to facilitate connection of multiple pairs of speakers or “Bi-Wiring”. Use the Speakers A connectors for the ‘main’ speakers and use the Speakers B connectors for a second pair, for example, extension speakers located in another room.

Under normal operation, connect the right speaker to the terminals market ‘R +’ and ‘R-’ ensuring that the ‘R+’ is connected to the ‘+’ terminal on your loudspeaker and the ‘R-’ is connected to the loudspeaker’s ‘-’ terminal. Connect the terminals marked ‘L+’ and ‘L-’ to the left speaker in the same way.

In Bridge Mode, connect the single speaker to the terminals marked ‘R +’ and ‘L+’ ensuring that the ‘L+’ is connected to the ‘+’ terminal on your loudspeaker and the R+ is connected to the loudspeaker’s ‘-’ terminal. Refer also to section “Bridge Mode” in this chapter (No. 6).

Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire to connect loudspeakers to your NAD C270. The high-current binding post terminals can be used as a screw terminal for cables terminating in spade or pin sockets or for cables with bare wire ends.

BARE WIRES AND PIN CONNECTORS

Bare wires and pin sockets should be inserted into the hole in the shaft of the terminal. Unscrew the speaker terminal’s plastic bushing until the hole in the screw shaft is revealed. Insert the pin or bare cable end into the hole and secure the cable by tightening down the terminal’s bushing. Ensure bare wire from the speaker cables does not touch the back panel or another socket . Ensure that there is only 1/2” (1cm) of bare cable or pin and no loose strands of speakers wire.

NOTE: Make sure the speaker impedance is 4 ohms or more when connecting only one pair of speakers; make sure the speaker impedance for all speakers is over 8 ohms when connecting two sets of speakers. In Bridge Mode, the impedance of the loudspeaker should also be 8 ohms or higher.

Always turn the C270 and other components in the system off before connecting or disconnecting speakers.

6. BRIDGE MODE

The stereo NAD C270 power amplifier can be configured to be mono (Bridge Mode), more than doubling its output power: 2 x 120 vs. 1 x 300 Watt. This way, the NAD C270 can be used as part of a high power stereo or home-theatre system, by connecting adding additional power amplifiers.

Set the BRIDGE MODE switch to the “Bridge” position and connect the speaker to the terminals marked ‘L +’ and ‘R+’ ensuring that the ‘L+’ is connected to the ‘+’ terminal on your loudspeaker and the ‘R+’ is connected to the loudspeaker’s ‘-’ terminal. Connect the source to the Left MAIN-IN input.

In Bridged Mode the NAD C270 will produce approximately 300W into an 8 ohm loudspeaker. In this mode, the amplifier sections will react as though the speaker impedance has been halved. Low impedance speakers (under 8 ohms) are not recommended when using Bridge Mode, as these may cause the amplifier’s thermal cut-out to operate if played at high levels.

The Bridge Mode indicator on the front panel (Fig. 2; No. 4) will illuminate when the amplifier is in Bridge mode.

NOTES: Do not connect anything to the Right “Fixed In” or Right “Variable In” sockets when Bridge Mode is selected.

Always turn the C270 and other components in the system off before connecting or disconnecting anything to the “Fixed In” or Variable In” sockets.

7. SOFT CLIPPING™

When an amplifier is driven beyond its specified power output, a hard, distorted sound can be heard on very loud sounds. This is caused by the amplifier cutting off or ‘hard clipping’ the peaks of sound that it was not designed to reproduce. The NAD Soft Clipping™ circuit gently limits the output of the system to minimise audible distortion if the amplifier is overdriven.

If your listening involves moderate power levels you may leave the Soft Clipping™ switch to Off. If you are likely to play at high levels, that could stretch the amplifier’s power capability, then switch Soft Clipping™ On.

The Soft Clipping™ indicator on the front panel will illuminate when the amplifier is in Soft Clip mode.

8. 12V TRIGGER AUTO ON-OFF

The C270’s 12V trigger input allows it to be switched to On and

Stand-by remotely by an external component.

Set the 12V Trigger switch set to the “ON” position to activate the 12V Trigger input. When the switch is set to the Off position, the 12V trigger input is not active. Refer to section “12V Trigger In” below for more information.

9. 12V TRIGGER IN

This input allows the C270 to be switched remotely to stand-by and on or by ancillary equipment such as a preamp, AV processor, etc. which are also equipped with a 12V trigger output.

For switching Stand-by/Power On of the C270 by an external component, connect the12V-trigger input of the C270 to the remote component’s DC output jack. The plug required is a standard 3.5mm Mini-Jack plug (“mono”): The tip is the live or

+ connection, the shaft of the input jack is the 12V-trigger - or GB ground connection.

NOTES: The C270’s 12V Trigger will work within a range of 6 to 15 V DC level and typically draws less than 10mA of current. Check the specifications of the Trigger output terminal on the remote component to ensure it is compatible with the C270’s 12V- trigger input. NAD components equipped with 12V output triggers are fully compatible with the C270’s 12V input trigger.

Before making any connections to any 12V trigger input or output, make sure all components are disconnected from the AC mains.

Failure to observe the above may result in damage to the C270 or any ancillary components attached to it. If in doubt over the connections, installation and operation of the 12V trigger output consult your NAD dealer.

10. AC LINE CORD

Plug the AC power cord into a live AC wall socket. Make sure all connections have been made before connecting to mains.

5

Page 5
Image 5
NAD C270 Speakers a & Speakers B, Bare Wires and PIN Connectors, Bridge Mode, Soft Clipping, 12V Trigger Auto ON-OFF

C270 specifications

The NAD C270 is a highly regarded power amplifier that has captured the attention of audiophiles and music enthusiasts alike. Known for its impressive performance and reliability, the C270 has become a staple in many home audio systems. This amplifier is part of NAD’s esteemed lineup, which is renowned for its commitment to high-quality sound reproduction and innovative technologies.

One of the key features of the NAD C270 is its robust construction. Built to withstand the rigors of everyday use, the amplifier features a solid chassis designed to minimize vibrations and protect internal components. This sturdy design not only enhances durability but also contributes to the overall sound quality, as stability is crucial for clarity in audio reproduction.

At the heart of the C270 is its impressive power output. The amplifier is capable of delivering a continuous RMS power of 130 watts per channel into 8 ohms, and it can increase its output to 200 watts per channel into 4 ohms. This significant power allows the C270 to drive a wide range of speakers, providing ample headroom for dynamic musical passages. Additionally, it features high current capability, which ensures excellent transient response, allowing it to handle the most demanding musical passages with ease.

The NAD C270 employs advanced technologies that improve its performance and efficiency. One notable feature is its use of NAD’s unique PowerDrive technology. This innovative design allows the amplifier to maintain its dynamic performance while ensuring reliability and protection against overheating. PowerDrive analyzes the output requirements and provides optimal power, ensuring consistent performance regardless of the speaker load.

Another significant aspect of the C270 is its dual-mono design, which provides independent amplification for each channel. This ensures that both the left and right channels operate without interference, resulting in a more immersive listening experience. The symmetrical layout also helps to minimize crosstalk, preserving the integrity of the audio signal.

In terms of connectivity, the C270 offers a variety of input options, allowing it to integrate seamlessly into any audio setup. With RCA inputs for standard connections and a low-level input for preamp connections, the amplifier caters to both classic and modern audio systems.

Overall, the NAD C270 is a powerful and versatile amplifier that embodies the essence of high-fidelity sound. Its combination of robust design, advanced technologies, and impressive performance makes it a popular choice for serious audio enthusiasts seeking to elevate their listening experience. Whether used with high-end speakers or as part of a home theater system, the C270 promises to deliver an audio experience that is both captivating and true to the original recordings.