NAD C715 owner manual Introduction, Getting Started, English Français Español Italiano

INTRODUCTION

GETTING STARTED

ENGLISH

FRANÇAIS

ESPAÑOL

ITALIANO

UNPACKING AND SETUP

WHAT’S IN THE BOX

Packed with your C 715 you will find:

•An AM loop antenna.

•A FM lead-type antenna.

•The SR 7 remote control with 2 (two) AAA batteries.

•This owner’s manual.

SAVE THE PACKAGING

Please save the box and all of the packaging in which your C 715 arrived. Should you move or otherwise need to transport your C 715, this is by far the safest container in which to do so. We’ve seen too many otherwise perfect components damaged in transit for lack of a proper shipping carton, so please: Save that box!

CHOOSING A LOCATION

Choose a location that is well ventilated (with at least several inches to both sides and behind), and that will provide a clear line of sight, within 23 feet/7 meters, between the C 715’s front panel and your primary listening/viewing position. This will ensure reliable infrared remote control communications.

The C 715 generates a modest amount of heat, but nothing that should trouble adjacent components. It is perfectly possible to stack the C 715 on top of other components.

QUICK START

In case you simply cannot wait to experience the performance of your new NAD C 715 CD Receiver, we provide the following “Quick Start” instructions to get you underway.

Please make all the connections to your C 715 with the unit unplugged. It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections.

DEALING WITH HUM AND NOISE

Hum and noise sometimes may prove a challenge in audio systems. Note these considerations to help prevent hum and noise problems:

•Power all your system's audio component from AC outlets originating from the same circuit of your house wiring. As far as possible, power all audio components from the same outlet, or adjacent outlets on the same circuit. It may be useful to power video displays (and computers!) from outlets on another circuit, especially if that circuit is supplied from the other "leg" of the house wiring.

•Do not bundle analog audio cables with AC power cables, or with coaxial digital-audio cables. It is best if they cross at right angles if they must be in close proximity.

•Employ high-quality, well-shielded audio cable throughout, and ensure that all connections are secure.

•A pencil-eraser can be used to burnish copper- and gold-plated contacts to ensure good, low-resistance contact; specialized contact- cleaners can also be useful. Avoid unnecessary unplugging and re-plugging since the gold (or copper) contact plating of typical cable connectors, even very high-quality ones, is very thin and easily worn.

Track down hum/noise problems one component at a time, working backwards from the C 715. That is

1Connect the speakers to the C 715 only, and check for hum.

2Then connect one component only (a CD player, for example) alone, with no other components connected and check for hum.

3Connect additional components, one at a time, to the C 715 and check for hum.

At each stage, if hum/noise appears, examine the audio cabling and AC- power routing of the new component. In some cases, moving the new component's AC cord to a different outlet, or installing a ground-lift (3-to-2- prong adapter) on its power cord, will eliminate the hum.

FACTORY DEFAULT SETTINGS

DEUTSCH NEDERLANDS SVENSKA

РУССКИЙ

PLAY A CD		Sometimes power spikes and drop-outs may from time to time cause some
• Connect your left and right front speakers to the C 715’s “L” and “R”		inadvertent functionality. The procedure below will set the C 715 to factory
outputs. Make sure to connect red to red (“+”) and black to black (“-”)		default settings
with care to avoid stray wires or strands crossing between terminals.		1 Turn OFF C 715 by pressing the power button in the front panel or SR 7
If your system includes a powered subwoofer, connect the C 715’s		remote control’s [OFF] key.
“SUBWOOFER OUT” jack to its line input.		2 Press and hold front panel’s [FM MODE /	] key for more than two
• Plug the AC mains plug into the AC outlet; the LED on the front panel		seconds. The C 715 will switch itself back ON and all the settings are
will be illuminated amber indicating the C 715 is in standby mode ready		restored to factory default settings.
to accept commands from either the front panel power switch or the
SR 7 remote.		Please note that setting the C 715 to factory default will delete all AM and
• To start CD playback, toggle [SOURCE] button in the front panel until		FM presets.
“CD” mode or press directly SR 7’s [CD] source key. Press	for the disc
tray to draw open.
• Insert the media and press the button to start playback.