NAD T 753 owner manual Rear Panel, English

REAR PANEL

NOTE: The T 753’s component-video inputs and outputs are fully wide-band, compatible with all HDTV formats. The T 753 does not display its on-screen menus on its component-video output. To use on-screen menus, you will need to make an S-Video or composite connection between the T 753 and the monitor/TV, and select it for menu display.

8DIGITAL IN OPT 1-2; COAX 3-6: Connect to the coaxial S/PDIF-format digital outputs of sources such as CD or DVD players, HDTV or satellite tuners, or other components; connect DIGITAL IN OPT1-2 to optical S/PDIF-format digital outputs.

DIGITAL OUT: Connect the optical and/or coaxial DIGITAL OUT ports to the corresponding S/PDIF digital input of a recording component such as a CD recorder, DAT deck, or computer soundcard. See "Setting Up the T 753".

9POWER: Press in to switch the A/V Receiver to standby mode. Pressing POWER again turns the unit OFF, recommended if you do not plan to use your A/V Receiver for an extended period of time. It is usual (and perfectly acceptable) to leave the T 753 in Standby mode in between normal viewing and listening sessions.

10SWITCHED AC OUTLET: This convenience jack can supply switched power to another component or accessory. It is powered on and off by the front panel POWER SWITCH (or the HTR2’s [On] and [Off] keys).

NOTE: The total draw of all devices connected to this jack must not exceed 120 watts.

11AC POWER INLET: Connect to the supplied IEC-standard removable AC power cord or a compatible cord.

12SPEAKERS A & B: Connect the left and right front, centre, left and right surround, and surround back speaker outputs to the corresponding loudspeakers. Each output’s “+” (red) terminal and “-“ (black) terminal must be connected to the corresponding “+” and “-“ terminals of the loudspeaker. Use extra care to ensure that no stray wires or strands cross between posts or terminals at either end.

Connect Speakers B left and right speaker outputs to the corresponding remote loudspeakers. When speakers B are activated the output is taken from the front left and right channels and any signal source is converted “downmixed” to stereo as indicated in the florescent display.

NOTE: Use stranded wire of at least 16 gauge (AWG); specialized speaker cable may be valuable (consult your NAD audio specialist). Connections to the T 753 can be made with banana plugs (US model only), or using bare wire, or pins, by loosening the terminal’s plastic nut, making a clean, neat connection, and re-tightening carefully (use the transverse hole through the post for bare-wire or pin connections). To minimize the danger of short-circuits, ensure that only 1/2-inch of exposed wire or pin is employed in connecting.

NOTE: This unit is designed to produce optimum sound quality when connected to speakers with impedances within the receiver’s operating range. Please check front, center, and surround speakers are rated to be 4Ω min. per speaker.

IMPORTANT NOTE: For optimum surround performance, the T 753 speaker settings and levels must be set correctly via the receiver’s setup routines; see “Setting Up the T 753”.

13DVD, SAT, VCR, VIDEO 4, VIDEO 5: These comprise the T 753’s principal inputs. Connect S-Video, composite video, and analog stereo audio from source components such as DVD players and HDTV/satellite tuners (see "Input Setup," below). VCR and VIDEO 4 may be used with recording components such as videocassette or DVD-recorders; connect the T 753 S-Video/composite video OUT jacks to these components’ record-inputs. (Note that VCR/VIDEO 4 may freely be used for play-only components, in which case their OUT jacks would remain unconnected.)

14MAIN IN/AUDIO PRE-OUTS/SUBWOOFER OUT: The T 753’s six built-in power amplifier channels will deliver excellent quality with even very demanding, low sensitivity home-theatre speaker systems. However, it is also possible to use the T 753 as a pre-amplifier with external power amplifiers for some or all channels (remove the supplied jumpers) if necessary. Unlike the six full range channels, there is no power amplifier built- into the T 753 for a subwoofer.

Connect the SW output 1, 2 or both to powered (“active”) subwoofers (or to power amplifier channels driving a passive system).

SURR-BACK-R jack will supply the same signal from the surround-back Left channel if the T 753 is so configured (see “Speaker Setup,” below). Either one or both channels are available mono or stereo as per “Speaker Setup”. Connect to one or two channels of an appropriate external power amplifier or other amplified component to furnish amplification for one or two surround back speakers. Your NAD audio specialist will be happy to advise you.

NOTE: Never connect the T 753’s speaker outputs and the speaker outputs of an external amplifier to the same speakers.

15TAPE IN/OUT: Connect the T 753’s TAPE OUT jacks to the stereo analog audio inputs, of an audio recording component such as a cassette deck or CD recorder, or of an outboard analog audio processor such as a stereo equalizer; connect the receiver’s TAPE IN jacks to the component’s corresponding outputs.

NOTE: Digital input signals are not available at the analog TAPE OUT jacks.

16MS OUT (MULTISOURCE OUT): Connect this pre-amp outputs to other zones using high-quality patch cables to reduce noise pickup over long distance runs.

177.1 CH. INPUT: Connect to the corresponding analog audio outputs of a multichannel source component such as a DVD-Audio or multichannel- SACD player, or external multichannel decoder. Typically, these sources will produce 5.1-channel output, in which case the SURROUND BACK jacks are left unconnected. The signals present at these jacks may be heard by selecting the front-panel EXT. 7.1 key or the HTR 2’s [Ext 7.1/5.1] button. See “Selecting Sources".

NOTE: There is no bass-management or other processing (other than master-volume control) available to this 7.1 CH. INPUT. While the multi- channel audio outputs of a DVD-Video player can be connected to these jacks, using the T 753’s own Dolby Digital and DTS decoding and digital- analog converters, via a digital connection, will usually produce superior results.

ENGLISH

13