Manuals / Brands / Household Appliance / Indoor Fireplace / Napoleon Fireplaces / Household Appliance / Indoor Fireplace

Napoleon Fireplaces BGD36NTR, BGD36PTR, GD36NTR, GD36PTR FIGURES, TOP EXIT, REAR EXIT, FIGURES 3a-d, CORNER TERMINATION, PERISCOPE TERMINATION, FIGURE 5A - GD36 ONLY, FIGURE 5B - BGD36 ONLY

1 32

Download 32 pages, 1.15 Mb

7

TYPICAL VENT INSTALLATIONS

REAR EXIT	TOP EXIT
	FIGURES 3a-d

*

For optimum performance, it is recommended that all horizontal runs have a 1 inch rise per foot.

When terminating vertically, the vertical rise is a minimum 36 inches and a maximum 40 feet from the centre of the fireplace flue outlet.

*When using rigid venting, this minimum vertical length may be reduced to 8½".

SPECIAL VENT INSTALLATIONS

PERISCOPE TERMINATION

CORNER TERMINATION

Use the GD201 periscope kit to locate the air termination above grade. The periscope must be installed so that when final grading is completed, the bottom air slot is located a minimum of 12 inches above grade. The maximum allowable vent length depends on the model of fireplace, as illustrated.

FIGURES 4

MODELS GD36: The maximum vent length for a corner installation is 24 inches, where only 6 inches of vertical rise is used. All corner installations require a minimum 6 inch rise. See FIGURE 5A.

MODELS BGD36: The maximum vent length for a corner installation is 20 inches of horizontal run, in addition to the 45° offset. In this case zero rise is acceptable when using rigid. Flexible venting must maintain a 6" rise. See FIGURE 5B.

FIGURE 5A - GD36 ONLY

20" MAX

TOP EXIT INSTALLATION

FIGURE 5B - BGD36 ONLY

REAR EXIT INSTALLATION

W415-0210 / E / 06.25.03

Contents

INSTALLATION AND OPERATION INSTRUCTIONS FOR NATURAL GAS MODEL MODEL PROPANE GAS MODEL R-2000 PG 2-5INTRODUCTION Warranty General Instructions General Information Care of Glass & Plated Parts Page GENERAL INSTRUCTIONS for example: in Massachusetts State: GD36 and BGD36 GENERAL INFORMATION GD36 GD36 SPECIFICATIONS BGD36 SPECIFICATIONS FIGURE 1a FIGURE 1b MODELS GD36 AND BGD36 MAY BE VENTED EITHER AS A TOP VENT OR A REAR VENT INSTALLATIONS CANADIAN U.S.A 12 INCHES Clearance above grade, veranda porch, deck or balcony REAR EXIT TOP EXIT FIGURES 3a-d PERISCOPE TERMINATION CORNER TERMINATION fireplace vent exit top exit rear exit horizontal termination vertical termination DEFINITIONS ELBOW VENT LENGTH VALUES -90° Formula 1: HT <VT Example 1: Formula 1: HT <4.2 Formula 2: HT + VT 24.75 feet Formula 1: HT <4.2 VT Formula 1: HT <VT Formula 1: HT <3.5VT Example 6: MAXIMUM Formula 1: HT <3VT Example 7: = V1 + V2 + V3 = 2 + 1 + 1.5 = 4.5 ft = H1 + H2 = 6 + 2 = 8 ft REAR EXIT: FIGURE BAFFLE TOP EXIT: FOR SAFE AND PROPER OPERATION OF THE FIREPLACE FOLLOW THE VENTING INSTRUCTIONS EXACTLY REAR EXIT TOP EXIT HORIZONTAL INSTALLATION See Note above Page not must not be removed. FIGURE FIREPLACE VENT CONNECTION W615-0033 W010-0370 VENT PIPE COLLAR GAS INSTALLATION Proceed once the vent installation is complete Route a 3/8" N.P.T. black iron gas line, 1/2 size: WIRE SIZE Page MANTLE CLEARANCES FIGURES 43a-c FIGURE 41a-b BGD36 NAILING TAB INSTALLATION NAILING DOOR REMOVAL & INSTALLATION FLANGE HOOD CLIP DOOR LATCH LOG PLACEMENT PHAZER FIGURE 46a-d The top of the log should rest in the pocket on the back log CHARCOAL EMBERS I N S T A L L A TION TO BE DONE BY A QUALIFIED IN white STALLER and must in the United States To safely install the fan, turn off the electricity first 60hz power cable to the junction box. At this point, it must be strain relieved and insulated To ease installation of the fan WARNING: depressed slightly MAINTENANCE PILOT BURNER ADJUSTMENT VENTURI ADJUSTMENT MODEL GD36 MODEL BGD36 WARNING: When ordering replacement parts always give the following information: & S COMPONENTS COMMON TO BOTH UNITS: #PART NO. DESCRIPTION Page SYMPTOM PROBLEM TEST SOLUTION Main burner goes Pilot flame is not large RESTICTING VERTICAL VENTS