9
FOR YOUR SAFETY READ BEFORE LIGHTING:
A. This fireplace is equipped with a pilot which must be lit by hand. While following these instructions exactly.
B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor.
C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a qualified service technician. Force or at- tempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water.
WHAT TO DO IF YOU SMELL GAS:
•Turn off all gas to the fireplace.
•Open windows.
•Do not try to light any appliance.
•Do not touch any electric switch; do not use any phone in your building.
•Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions.
•If you cannot reach your gas supplier, call the fire depart- ment.
| OL |
|
|
|
|
| O |
|
| N | F |
| HI | O | F |
|
| TOLIP | |
| FLAME |
| |
|
|
| |
TO LPI | ADJUSTMENTPILOT | ||
| KNOB | ON/OFF | |
| KNOB | ||
|
| ||
LIGHTING INSTRUCTIONS
When lighting and
1.Stop! Read the above safety information on this label.
2.Turn off all electric power to the fireplace.
3.Turn the gas knob clockwise to off.
4.Wait five (5) minutes to clear out any gas. If you smell gas including near the floor. Stop! Follow "B" in the above safety information on this label. If you don't smell gas go the next step.
5.Find pilot located in front of back log.
6. Turn gas knob
7.Depress slightly and hold gas knob while lighting the pilot with the push button ignitor. Keep knob depressed for one minute, then release. If pilot does not continue to burn, re- peat steps 3 through 7.
8.With pilot lit, depress and turn gas knob
9.If equipped with flame adjustment valve, push and turn knob to high.
10.If equipped with remote
11.Turn on all electric power to the fireplace.
TO TURN OFF GAS
1.Turn off all electrical power to the unit if service is to be performed.
2.Push in gas control knob slightly and turn clockwise to off. Do not force.
MAINTENANCE
TURN OFF THE GAS AND UNPLUG ELECTRICAL POWER BEFORE SERVICING THE FIREPLACE INSERT!
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servic- ing. This insert and its venting system should be in- spected before use and at least annually by a qualified service person. The fireplace area must be kept clear and free of combustible materials, gasoline or other flam- mable vapours and liquids. The flow of combustion and ventilation air must not be obstructed.
1. In order to properly clean the burner and pilot assembly, remove the logs exposing both assemblies.
2. Keep the control compartment, logs, burner, air shutter opening and the area surrounding the logs clean by vacu- uming or brushing, at least once a year.
3. Check to see that all burner ports are burning. Clean out any of the ports which may not be burning or are not burn- ing properly.
4. Check to see that the pilot flame is large enough to engulf the thermocouple on one leg and reaches toward the burner on the other leg.
5. Replace the cleaned logs.
6. Check to see that the main burner ignites completely on all openings when the gas knob for the burner is turned on. A
7.Check that the door gasketing is not broken or missing. Replace if necessary.
Remove the pilot screw cap. Adjust the pilot screw to pro- vide properly sized flame. Turn in a clockwise direction to reduce the gas flow. Replace the pilot screw cap.
Natural gas has the air shutter set at 1/4" opening; pro- pane has the air shutter set at 3/8" opening. Closing the air
