National Instruments NI 6115, NI 6120 - page 20

Chapter 1 Introduction

© National Instruments Corporation 1-9 NI 6115/6120 User Manual

The following is a description of installation categories:

• Installation Category I is for measurements performed on circuits not

directly connected to MAINS1. This category is a signal level such as

voltages on a printed wire board (PWB) on the secondary of an

isolation transformer.

Examples of Installation Category I are measurements on circuits not

derived from MAINS and specially protected (internal)

MAINS-derived circuits.

• Installation Category II is for measurements performed on circuits

directly connected to the low-voltage installation. This category refers

to local-level distribution such as that provided by a standard wall

outlet.

Examples of Installation Category II are measurements on household

appliances, portable tools, and similar equipment.

• Installation Category III is for measurements performed in the building

installation. This category is a distribution level referring to hardwired

equipment that does not rely on standard building insulation.

Examples of Installation Category III include measurements on

distribution circuits and circuit breakers. Other examples of

Installation Category III are wiring including cables, bus-bars, junction

boxes, switches, socket outlets in the building/fixed installation, and

equipment for industrial use, such as stationary motors with a

permanent connection to the building/fixed installation.

• Installation Category IV is for measurements performed at the source

of the low-voltage (<1,000 V) installation.

Examples of Installation Category IV are electric meters, and

measurements on primary overcurrent protection devices and

ripple-control units.

1 MAINS is defined as the electricity supply system to which the equipment concerned is designed to be connected either for

powering the equipment or for measurement purposes.

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Compliance FCC/Canada Radio Frequency Interference Compliance Determining FCC Class FCC/DOC Warnings Class A Compliance to EU Directives Contents Chapter 4 Connecting Signals Page About This Manual Conventions National Instruments Documentation Related Documentation Introduction About the NI 6115/6120 Using PXI with CompactPCI What You Need to Get Started Software Programming Choices NI-DAQ National Instruments ADE Software Optional Equipment Custom Cabling Unpacking Safety Information Page Page Installing and Configuring the NI 6115/6120 Installing the Software Installing the Hardware Page Configuring the Device National Instruments Corporation 3-1 NI 6115/6120 User Manual Hardware Overview DAQ - STC RTSI Bus Figure 3-1. NI 6115 Block Diagram Analog Input The following sections describe in detail each AI category. Input Mode Note The inputs are differential only in the sense that the ground loops are broken. I/O Connector Input Polarity and Input Range Considerations for Selecting Input Ranges Input Coupling Analog Output Analog Trigger Figure 3-3. Analog Trigger Block Diagram for the NI 6115/6120 Figure 3-4. Below-Low-Level Analog Triggering Mode Page Antialiasing Filters Phase-Locked Loop Circuit Correlated Digital I/O Timing Signal Routing Page Programmable Function Inputs Device and RTSI Clocks RTSI Triggers Page Figure 3-13. PXI RTSI Bus Signal Connections Connecting Signals I/O Connector Figure 4-1. I/O Connector Pin Assignment for the NI 6115/6120 I/O Connector Signal Descriptions Table 4-2. Signal Descriptions for I/O Connector Pins Table 4-2. Signal Descriptions for I/O Connector Pins (Continued) Table 4-3. Analog I/O Signal Summary for the NI 6115 Table 4-2. Signal Descriptions for I/O Connector Pins (Continued) Table 4-4. Analog I/O Summary for the NI 6120 Table 4-5. Digital I/O Signal Summary Types of Signal Sources Floating Signal Sources Table 4-5. Digital I/O Signal Summary (Continued) Ground-Referenced Signal Sources Connecting Analog Input Signals Connections for Ground-Referenced Signal Sources * Figure 4-2. Pseudodifferential Input Connections on the NI 6115 forGro und-Referenced Signals Figure 4-3. Pseudodifferential Input Connections on the NI 6120 forGro und-Referenced Signals Connections for Nonreferenced or Floating Signal Sources * Figure 4-4. Differential Input Connections on the NI 6115 for Nonreferenced Signals Common-Mode Signal Rejection Considerations Working Voltage Range Connecting Analog Output Signals Connecting Digital I/O Signals Correlating DIO Signal Connections Page Power Connections Connecting Timing Signals Page Programmable Function Input Connections DAQ Timing Connections TRIG1 Signal TRIG2 Signal Page STARTSCAN Signal Page CONVERT* Signal AIGATE Signal SISOURCE Signal SCANCLK Signal EXTSTROBE* Signal Waveform Generation Timing Connections WFTRIG Signal UPDATE* Signal UISOURCE Signal General-Purpose Timing Signal Connections GPCTR0_SOURCE Signal GPCTR0_GATE Signal GPCTR0_OUT Signal GPCTR0_UP_DOWN Signal GPCTR1_SOURCE Signal GPCTR1_GATE Signal GPCTR1_OUT Signal Figure4-34 shows the timing requirements for GPCTR1_OUT. Figure 4-35. GPCTR1_OUT Signal Timing Figure 4-36. GPCTR Timing Summary GPCTR1_UP_DOWN Signal FREQ_OUT Signal Field Wiring Considerations Calibration Loading Stored Calibration Constants Self-Calibration External Calibration Page A Specifications Analog Input Input Characteristics DC Transfer Characteristics Table A-1. NI 6115 Analog Input DC Accuracy Information Table A-2. NI 6120 Analog Input DC Accuracy Information Dynamic Characteristics Table A-4. NI6120 Analog Input Dynamic Charac teristics Figure A-1. NI 6115 Total Harmonic Distortion Plus Noise (THD+N) Figure A-2. NI 6120 Total Harmonic Distortion Plus Noise (THD+N) Figure A-3. NI6115 High-Voltage THD + N Figure A-4. NI 6120 High-Voltage THD+ N Figure A-5. NI 6115 THD + N with Filters Stability Analog Output Output Characteristics DC Transfer Characteristics Voltage Output Dynamic Characteristics Stability Digital I/O Timing I/O Triggers Analog Trigger Page Safety Maximum Working Voltage Electromagnetic Compatibility B Common Questions General Information Installing and Configuring the Device Analog Input and Output Page Timing and Digital I/O Page C Technical Support and Professional Services Glossary Numbers/Symbols A B C D E F G H I K L M N O P R S T U V W Index Numerics A B C D E F G H I K L M N O P Q R S Page T U V W