Manuals / Brands / Computer Equipment / Switch / National Instruments / Computer Equipment / Switch

National Instruments NI 6115, NI 6120 GPCTR0_UP_DOWN Signal, GPCTR1_SOURCE Signal

1 127

Download 127 pages, 1.22 Mb

Chapter 4 Connecting Signals

© National Instruments Corporation 4-35 NI 6115/6120 User Manual

GPCTR0_UP_DOWN Signal

This signal can be received as an input on the DIO6 pin and is not available

as an output on the I/O connector. The general-purpose counter 0 counts

down when this pin is at a logic low and count up when it is at a logic high.

You can disable this input so that software can control the up-down

functionality and leave the DIO6 pin free for general use.

GPCTR1_SOURCE Signal

Any PFI pin can receive as an input the GPCTR1_SOURCE signal, which

is available as an output on the PFI3/GPCTR1_SOURCE pin.

As an input, GPCTR1_SOURCE is configured in the edge-detection mode.

You can select any PFI pin as the source for GPCTR1_SOURCE and

configure the polarity selection for either rising or falling edge.

As an output, GPCTR1_SOURCE monitors the actual clock connected to

general-purpose counter 1, even if another PFI is externally generating the

source clock. This output is set to high-impedance at startup.

Figure4-33 shows the timing requirements for GPCTR1_SOURCE.

Figure 4-33. GPCTR1_SOURCE Signal Timing

The maximum allowed frequency is 20MHz, with a minimum pulse width

of 10 ns high or low. There is no minimum frequency limitati on.

The 20MHz or 100 kHz timebase normally generates GPCTR1_SOURCE

unless you select some external source.

tp = 50 ns minimum

tw = 10 ns minimum

twtw

tp

Contents

Main Page Important Information Warranty Copyright Trademarks Patents Compliance FCC/Canada Radio Frequency Interference Compliance Determining FCC Class FCC/DOC Warnings Class A Compliance to EU Directives Contents Chapter 4 Connecting Signals Page About This Manual Conventions National Instruments Documentation Related Documentation Introduction About the NI 6115/6120 Using PXI with CompactPCI What You Need to Get Started Software Programming Choices NI-DAQ National Instruments ADE Software Optional Equipment Custom Cabling Unpacking Safety Information Page Page Installing and Configuring the NI 6115/6120 Installing the Software Installing the Hardware Page Configuring the Device National Instruments Corporation 3-1 NI 6115/6120 User Manual Hardware Overview DAQ - STC RTSI Bus Figure 3-1. NI 6115 Block Diagram Analog Input The following sections describe in detail each AI category. Input Mode Note The inputs are differential only in the sense that the ground loops are broken. I/O Connector Input Polarity and Input Range Considerations for Selecting Input Ranges Input Coupling Analog Output Analog Trigger Figure 3-3. Analog Trigger Block Diagram for the NI 6115/6120 Figure 3-4. Below-Low-Level Analog Triggering Mode Page Antialiasing Filters Phase-Locked Loop Circuit Correlated Digital I/O Timing Signal Routing Page Programmable Function Inputs Device and RTSI Clocks RTSI Triggers Page Figure 3-13. PXI RTSI Bus Signal Connections Connecting Signals I/O Connector Figure 4-1. I/O Connector Pin Assignment for the NI 6115/6120 I/O Connector Signal Descriptions Table 4-2. Signal Descriptions for I/O Connector Pins Table 4-2. Signal Descriptions for I/O Connector Pins (Continued) Table 4-3. Analog I/O Signal Summary for the NI 6115 Table 4-2. Signal Descriptions for I/O Connector Pins (Continued) Table 4-4. Analog I/O Summary for the NI 6120 Table 4-5. Digital I/O Signal Summary Types of Signal Sources Floating Signal Sources Table 4-5. Digital I/O Signal Summary (Continued) Ground-Referenced Signal Sources Connecting Analog Input Signals Connections for Ground-Referenced Signal Sources * Figure 4-2. Pseudodifferential Input Connections on the NI 6115 forGro und-Referenced Signals Figure 4-3. Pseudodifferential Input Connections on the NI 6120 forGro und-Referenced Signals Connections for Nonreferenced or Floating Signal Sources * Figure 4-4. Differential Input Connections on the NI 6115 for Nonreferenced Signals Common-Mode Signal Rejection Considerations Working Voltage Range Connecting Analog Output Signals Connecting Digital I/O Signals Correlating DIO Signal Connections Page Power Connections Connecting Timing Signals Page Programmable Function Input Connections DAQ Timing Connections TRIG1 Signal TRIG2 Signal Page STARTSCAN Signal Page CONVERT* Signal AIGATE Signal SISOURCE Signal SCANCLK Signal EXTSTROBE* Signal Waveform Generation Timing Connections WFTRIG Signal UPDATE* Signal UISOURCE Signal General-Purpose Timing Signal Connections GPCTR0_SOURCE Signal GPCTR0_GATE Signal GPCTR0_OUT Signal GPCTR0_UP_DOWN Signal GPCTR1_SOURCE Signal GPCTR1_GATE Signal GPCTR1_OUT Signal Figure4-34 shows the timing requirements for GPCTR1_OUT. Figure 4-35. GPCTR1_OUT Signal Timing Figure 4-36. GPCTR Timing Summary GPCTR1_UP_DOWN Signal FREQ_OUT Signal Field Wiring Considerations Calibration Loading Stored Calibration Constants Self-Calibration External Calibration Page A Specifications Analog Input Input Characteristics DC Transfer Characteristics Table A-1. NI 6115 Analog Input DC Accuracy Information Table A-2. NI 6120 Analog Input DC Accuracy Information Dynamic Characteristics Table A-4. NI6120 Analog Input Dynamic Charac teristics Figure A-1. NI 6115 Total Harmonic Distortion Plus Noise (THD+N) Figure A-2. NI 6120 Total Harmonic Distortion Plus Noise (THD+N) Figure A-3. NI6115 High-Voltage THD + N Figure A-4. NI 6120 High-Voltage THD+ N Figure A-5. NI 6115 THD + N with Filters Stability Analog Output Output Characteristics DC Transfer Characteristics Voltage Output Dynamic Characteristics Stability Digital I/O Timing I/O Triggers Analog Trigger Page Safety Maximum Working Voltage Electromagnetic Compatibility B Common Questions General Information Installing and Configuring the Device Analog Input and Output Page Timing and Digital I/O Page C Technical Support and Professional Services Glossary Numbers/Symbols A B C D E F G H I K L M N O P R S T U V W Index Numerics A B C D E F G H I K L M N O P Q R S Page T U V W