National Instruments PC-LPM-16/PnP , Interrupt Selection

Appendix C Using Your PC-LPM-16 (Non-PnP) Board



National Instruments Corporation C-9 PC-LPM-16/PnP User Manual

Note:

Base I/O address values hex 000 through 0FF are reserved for system use.

Base I/O address values hex 100 through 3FF are available on the I/O

channel.

Interrupt Selection

The PC-LPM-16 connects to any one of the six interrupt lines of the

computer I/O channel. A jumper selects the interrupt line on one of the

double rows of pins located above the I/O slot edge connector on the

PC-LPM-16 (see Figure C-1). To use the PC-LPM-16 interrupt

capability, select an interrupt line and place the jumper in the

appropriate position to enable that particular interrupt line.

The interrupt lines that the PC-LPM-16 hardware supports are

IRQ<3..7>, and IRQ9.

Note:

Using interrupt line 6 is not recommended. The diskette drive controller

uses interrupt line 6 on most IBM PC and compatible computers.

After you select an interrupt level, place the interrupt jumper on the

appropriate pins to enable the interrupt line.

The interrupt jumper setting is

W3

. The default interrupt line is IRQ5,

which you select by placing the jumper on the pins in row 5, as shown

in Figure C-3. To change to another line, remove the jumper from IRQ5

and place it on the new pins.

1 1 0 1 0 340 340–34F

1 1 0 1 1 360 360–36F

1 1 1 0 0 380 380��38F

1 1 1 0 1 3A0 3A0–3AF

1 1 1 1 0 3C0 3C0–3CF

1 1 1 1 1 3E0 3E0–3EF

Table C-3.

Switch Settings with Corresponding Base I/O Address and

Base I/O Address Space (Continued)

Switch Setting Base I/O Address

(hex) Base I/O Address

Space Used (hex)

A9 A8 A7 A6 A5

Contents

Main Page Important Information WARNING REGARDING MEDICAL AND CLINICAL USE OF NATIONAL INSTRUMENTS PRODUCTS Trademarks Copyright Page Page Glossary Index Figures Tables About This Manual Organization of This Manual Conventions Used in This Manual National Instruments Documentation Related Documentation Customer Communication Introduction About the PC-LPM-16/PnP What You Need to Get Started LabVIEW and LabWindows/CVI Application Software Software Programming Choices NI-DAQ Driver Software Register-Level Programming Optional Equipment Custom Cables Unpacking Installation and Configuration Hardware Installation Software Installation Plug and Play Board Configuration Base I/O Address and Interrupt Selection Non-Plug and Play Theory of Operation Functional Overview Chapter 3 Theory of Operation Figure 3-1. PC-LPM-16PnP Block Diagram PC I/O Channel Interface Circuitry Analog Input and Data Acquisition Circuitry Analog Input Circuitry Data Acquisition Timing Circuitry Single-Channel Data Acquisition Data Acquisition Rates Multichannel Scanning Data Acquisition Chapter 3 Theory of Operation PC-LPM-16/PnP User Manual 3-8 Digital I/O Circuitry Digital I/O Circuitry Block Diagram Figure 3-4. Timing I/O Circuitry Page Signal Connections I/O Connector Chapter 4 Signal Connections Figure 4-1. PC-LPM-16PnP I/O Connector Pin Assignments Signal Connection Descriptions Page Analog Input Signal Connections Connections for Signal Sources Digital I/O Signal Connections Power Connections Power Rating Data Acquisition Timing Connections Timing Connections General-Purpose Timing Signal Connections and General-Purpose Counter Timing Signals Page Page Page Specifications A Transfer Characteristics PC-LPM-16PnP Board Amplifier Characteristics Digital I/O Stability Dynamic Characteristics Timing I/O Bus Interface Explanation of Analog Input Specifications Environment Physical Page Page B MSM82C53 Data Sheet Page Page Page Page Page Page Page Page Page Page Page Using Your PC-LPM-16 (Non-PnP) Board C the PC-LPM-16 Differences between the PC-LPM-16PnP and Page Page Configuration and Installation of the Board Configuration PC-LPM-16 (non-PnP) Page Base I/O Address Selection Page Page Interrupt Selection Analog Input Jumper Settings 5 V) Bipolar Input Selection 1 ( Bipolar Input Selection 2 ( Unipolar Input Selection 1 (0 to 10 V) Select the bipolar ( 2.5 V) 2.5 V) input configuration by setting jumpers W1 and W2 as shown in Figure C-6. Unipolar Input Selection 2 (0 to 5 V) Installation Register-Level Programming D Register Map Base Address Register Size Register Descriptions Register Description Format Configuration and Status Register Group Page Page Page Command Register 2 Command Register 2 Command Register 3 Status Register 1 Status Register 1 Page Status Register 2 Analog Input Register Group A/D FIFO Low-Byte Register and A/D FIFO High-Byte Register A/D FIFO Low-Byte Register and A/D FIFO High-Byte Register A/D Clear Register Counter/Timer (MSM82C53) Register Group Counter 0 Data Register Counter 1 Data Register Counter 2 Data Register Page Page Page Timer Interrupt Clear Register Digital I/O Register Group Digital Output Register Digital Input Register Programming Considerations Register Programming Considerations Initializing the PC-LPM-16/PnP Programming the A/D Calibration Programming the Analog Input Circuitry Analog Input Circuitry Programming Sequence A/D FIFO Output Binary Modes Clearing the Analog Input Circuitry Programming Multiple A/D Conversions on a Single Input Channel Using Counter 0 Page Page Programming Multiple A/D Conversions Using External Timing Programming Multiple A/D Conversions with Channel Scanning A/D Interrupt Programming Programming the Digital I/O Circuitry Programming the MSM82C53 Counter/Timer Customer Communication FTP Support Electronic Services E Bulletin Board Support Telephone and Fax Support Telephone Fax Fax-on-Demand Support E-Mail Support (currently U.S. only) Technical Support Form PC-LPM-16/PnP Hardware and Software Configuration Form Other Products National Instruments Products Documentation Comment Form Glossary Symbols A C B Page Page T V A Numbers Index B C D E I H F G J P N M O R S T U