Preface, Safety Requirements Audience | NCR 5953 specs

i

Preface

Safety Requirements

Caution: This device should only be powered by a power source which meets Safety Extra Low Voltage (SELV) and LPS (Limited Power Source) requirements per UL1950, IEC 950, and EN 60 950. The power source must be certified by the appropriate safety agency for the country of installation.

Audience

This manual is written for hardware installer/service personnel, system integrators, programmers, and field engineers.

Image 3

NCR 5953 manual Preface, Safety Requirements Audience

Contents

User Guide Page Preface Safety Requirements AudiencePage Table of Contents USB DynaKey Migration MSR Powered USB 12 V to 2 x 4 Locking Connector Revision Record Voluntary Control Council for Interference Vcci Radio Frequency Interference StatementsFederal Communications Commission FCC Canadian Department of Communications European Contact Declaration of ConformityPage Introduction Features CompatibilityController Board Multi-Color Power LED Keylock Positions External Standard PC Keyboard Connector Integrated 2 x 20 Customer Display Special PC Setup Keypad LayoutThree-Track MSR or Two-Track JIS MSR Speaker Overview Transit Range Physical EnvironmentOperating Range Storage Range Power Consumption Electrical RequirementsCable Length Limitations Dimensions 5953-K023 Checkstand Mount Mm 10.75 200 mm 140 mm 105 mm Site Preparation Hardware Installation Serial Number Location Mounting Options Cable Connector Access Installing a Remote Table Top USB DynaKey Installing a USB DynaKey DVI 5972-F040 Installing an Integrated Customer Display 19850 Assemble the post components Phillips PH Screw Integrated Display Bracket 19851 Installing a 5953-K023 Checkstand Mount Installing a Checkstand Mounted DynaKey Checkstand Base Upper Half Front Cover Thumbscrew 17323 17449 Special Keypad Mode Powering Up Power up the system Hardware Installation Normal Operating Mode Screen Saving Feature Hardware Installation USB DynaKey Capabilities Firmware Fpga Firmware Defaults Unique POS CapabilitiesNCRUsbKeyboardCtl HID usages Keymatrixusage NCR Proprietary HID Usages Double-high/Double-wide Keys Programmable Key Matrix Sorted by Offset Sorted by KeyNumber Keyboard Matrix for 5953 USB DynaKey Sorted by Offset Sorted by KeyNumber Sorted by Offset Sorted by KeyNumber USB DynaKey Tone Frequencies Configurable Key Click Tone NCR USB DynaKey Control NCR Platform Software Components Programming Key-Value Definitions NCR USB DynaKey Control Parameterization Registry Values Set USB Key Matrix Application NCR USB DynaKey Control Data Capture Registry Values Set USB Key Clicks Application Command-line Parameters Command-line Parameters Inch USB DynaKey Video Drivers Page Overview USB DynaKey Migration 5953 USB DynaKey Migration LCD Discussion LCD 800x600 High-Bright Long-Life Color LCD InterfaceTouch option POS-Checkout Style Keyboard Hot Plug Double-High / Double-Wide Keys Keyboard Programmability Error Tone KeylockKey Click Fingerprint Sensor Power LEDScanner port Additional ports Smartcard Reader Key Re-mapping Registry Manipulation Tool 5953 USB DynaKey Migration USB DynaKey Migration 5953 USB DynaKey Migration Safety Requirements Hardware Service Troubleshooting Table Problem Isolation Procedures Symptom Probable Cause Solution LED Disassembling the DynaKey Servicing the DynaKey Module Removing the Remote Table Top Mount Removing the Back Cover Removing the MSR Removing the Speaker Assembly MSR Cleaning Cards Removing the Controller Board 20067 Removing the LCD Remove the screws 4 that secure the LCD to the LCD Bracket Removing the Keypad Removing the Keylock Adapter Assembly Re-Assembling the DynaKey Replacing the Keylock assembly Controller Board Connector Identification DVI Connector Connector Pin-Out Information Powered USB Connector USB Connectors DVI to Champ Powered USB 12 V to 2 x 4 Locking ConnectorCables DVI to DVI Cleaning the Glass DynaKey Cleaning Procedures Index NCRUsbKeyboardCtl, 4-12,4-13