NEC NP4000 Enter, Enter, Enter, Setup, Cancel

4. Convenient Features

You are prompted to enable the Security Function. Select OK and press Enter.

Select On using the ▼ button.

The keyword window is dis- played. Enter a keyword between 4 and 10 characters using ▲▼◄►. Press Enter.

Once a successful keyword is entered, a confirmation screen is displayed. Enter the same password as the previous step and write it down for later reference. Press Enter. A security activation message is displayed. Select Cancel to return to the Setup menu or select OK to enable security.

Contents

Projector Notes Important Information Safety Cautions Important Information Laser Rating CAUTION Disposing of your used product WARNING TO CALIFORNIA RESIDENTS: RF Interference (for USA only) zReorient or relocate the receiving antenna zIncrease the separation between the equipment and receiver zConsult the dealer or an experienced radio / TV technician for help Important Safeguards Place the projector in a horizontal position Fire and Shock Precautions rear Page Remote Control Precautions Lamp Replacement Important Lamp Characteristic Table of Contents Table of Contents 6. MAINTENANCE 7. APPENDIX 8. SPECIFICATIONS 9. TROUBLESHOOTING CHECK LIST 1. Introduction nWhat’s in the Box oIntroduction to the Projector pPart Names of the Projector Page Page Height adjusters Adjust projection height Color wheel cooling vent – do not obstruct Front filter Keep the fan free of dust – clean regularly qTop Features Page Page rTerminal Panel Features When connected to the screen through a com SC TRIGGER mercially available cable, the screen deploys automatically on start up of the projector. The screen retracts when the projector is powered sPart Names of the Remote Control Important: Power OFF Power On Insert the supplied batteries taking note of the polarity (+/-)as shown Replace the cover locator (A), and then click locking catch into place (B) Page Page 2. Installation and Connections nSetting Up the Screen and the Projector oSelecting a Location pInstalling or Removing the Optional Lens 2.Push the LENS RELEASE button all the way in and rotate the lens counterclockwise The existing lens will be disengaged 3. Pull out the existing lens slowly 1. Insert the lens with the arrow mark on top 2. Rotate the lens clockwise until you feel it click into place Page qThrow Distance and Screen Size Page rReplacing Color Wheel Page Secure the retaining screws as shown Align the lamp cover (A)with the arrow mark on the cabinet and slide it into place (A) 10. Secure the captive screw (B) sMaking Connections Enabling the computer’s external display Page Page Component Page tConnecting the Supplied Power Cable 3. Projecting an Image (Basic Operation) nTurning on the Projector 3. Projecting an Image (Basic Operation) Enter oSelecting a Source pAdjusting the Picture Position and Picture Size The window is displayed. Select the desired picture size using ▲or▼ and press 5. When finished, press Exit to return to the projected image Press the Lens Shift button to bring up the Lens Shift window Aspect Page qOptimizing an RGB Image Automatically rAdjusting Volume Up and Down sTurning off the Projector Page 4. Convenient Features nTurning Off the Image and Sound oFreezing a Picture pAdjusting the Focus/Zoom Manually qChanging Lamp Mode Press the Lamp Mode button on the remote control to access the Lamp Mode menu From the window, select using ▲or▼. Move the cursor to and press rGetting Information sAdjusting Position/Clock Keystone ADJUSTMENT HORIZONTAL VERTICAL Keystone Max. +/– 35° approx tPreventing the Unauthorized Use of the Projector Cancel Page uUsing the Physical Lock 5. Using On-ScreenDisplay nUsing the Menus Page oMenu Tree Page pMenu Elements qSource Menu Descriptions and Functions rAdjust Menu Descriptions and Functions Aspect Select Aspect Ratio using ◄or► from the list (see page 65) Ratio Overscan Set the Overscan value using ◄or► (see page 65) Aspect Ratio Overscan Noise Select Noise Reduction mode (see page 67) Reduction 3D Y/C Select 3D Y/C Separation mode (see page 67) Noise Reduction 3D Y/C Separation Deinterlace Color Matrix Telecine sDetail Settings Menu Descriptions and Functions Reference Gamma Correction Brightness R Set the Brightness R value to compensate for red light sources Brightness G Set the Brightness G value to compensate for green light sources Brightness B Set the Brightness B value to compensate for blue light sources Contrast R Set the Contrast R value to compensate for red light sources Contrast G Set the Contrast G value to compensate for green light sources Red Increase or decrease the amount of red in the projected output using ◄ and ► Increase or decrease the amount of green in the projected output using ◄ and ► tSetup Menu Descriptions and Functions Keystone Lamp Mode Lamp Select Lamp Interval Menu Mode Language Orientation Select from four projection methods depending on projection site (see page 78) Communication Select Communication Speed Orientation Communication Speed Menu Color Select Display Time Background Security Control Panel Lock DynamicBlack Remote Sensor LAN Settings Standby Mode PC Control DHCP Select either a static IP or DHCP IP setting by selecting the appropriate radio button IP Address Displays the IP address Auto Start Set this item on to enable the projector to power up when AC plug in Range: on or off Power Select the amount of time the projector remains idle before powering Auto Start Note: Power Management Screen Trigger Fan Mode Default Source Select Color System Filter Message uInformation Menu Descriptions and Functions Page Page Product Displays Product ID Serial Number Displays projector Serial Number Firmware vReset Menu Descriptions and Functions 6. Maintenance nCleaning the projector 6. Maintenance Please clean filter Lift the projector to Bottom view expose the underside to locate the first filter See the drawing on the right 3. The rear filter can be accessed as shown Clear Filter Hours oReplacing Consumable Parts Insert replacement foam and press down firmly Replace the filter covers by pushing gently in the direction shown Lamps last approximately Page Press the ▲or▼ button to move to the Reset menu and press Enter Clear Lamp confirmation box is dis- played. Select 7. Appendix nUsing the Optional Remote Mouse Receiver (NP01MR) 7. Appendix Note: oTroubleshooting The Power LED The Status LED The Lamp LEDs Page pImage Problems 7.Appendix Problem: The lamp goes off Problem: The projector does not respond to the remote control Problem: There is no sound Problem: The sound is distorted qHaving the Projector Serviced 8. Specifications nProjector Specifications 8. Specifications Page Page oCabinet Dimensions pPin Assignments of Mini D-Sub15 Pin Input Connector qCompatible Input Signal List "D rPC Control Codes and Cable Connections Page sScreen Trigger tOperation Using HTTP Browser Domain Mail Test Mail PJLink http:// <the projector's IP address> /index.html SETTING information) u15 Pin GPIO Control 9. Troubleshooting Check List 9. Troubleshooting Check List Other In the space below please describe your problem in detail Information on application and environment where your projector is used