Manuals / NEC / Computer Equipment / Computer Monitor

NEC PX-50XM4G user manual Creating a video wall, Cable Management, Information, Confidential

Models: PX-50XM4G

1 40

Download 40 pages 42.62 Kb

Page 9

Creating a video wall

Creating a video wall

With built-in matrix display capability, you can create a 4-25 video wall.

• Connect signal cables and remote cables as shown below.

Video signal		RGB/DVD/HD signal

BNC connector

				(	VIDEO	BNC connector	OUT
				VIDEO1 I N / OUT)			OUT
				VIDEO1 I N / OUT)			VIDEO Signal	RGB signal/	IN
	RCA phono plug	VIDEO 3			VIDEO 2		VIDEO Signal		IN

IN								DVD/HD signal
IN								DVD/HD signal
VIDEO Signal		(		1AUDIO R
		)	L	1AUDIO R
		MONO
				Y
					DVD1

Remote	IN	I N
control	REMOTE	OUT	OUT	control
control			OUT	Remote
				Remote

Remote IN control

Cr/Pr	R/
G/ Y		RGB2
Cb/Pb	B/	/ DVD2
HD		/ HD2
VD
( IN / OUT		RGB 1
)
I N
REMOTE
OUT

CONFIDENTIAL

	OUT	RGB signal/
		DVD/HD signal

OUT Remote control

Note:

1.The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit, that will place an extraordinary load on the other unit and may damage it.

2.LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.

3.LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.

Information

•To loop signals out to another plasma display, set the LOOP OUT to ON.

•To create a video wall, set the VIDEO WALL menu items properly.

•To connect monitors, please use a 1~2m (3.3~6.6 feet) BNC cable (any commercially available cable).

•If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

•Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024768, 60Hz signal.

•A distribution amplifier is particularly recommended when using 9-screen and over video wall.

•From the second monitor onward, connections require a BNC-RCA conversion cable or connector, a mini D-Sub 15 pin cable-BNC (5) cable or a conversion connector.

Cable Management

Using the cable-clamps provided with the plasma display, bundle at the back of the unit the signal and audio cables connected to the display.

Back of the unit

mounting holes

To attach	To detach
1.	2.
	clamp
	cables
mounting hole

Downloaded From TV-Manual.com Manuals

E-5

4-9

Image 9

NEC PX-50XM4G Creating a video wall, Cable Management, Information, Confidential, Downloaded From TV-Manual.com Manuals

Contents

Downloaded From TV-Manual.com Manuals CONFIDENTIALPlasmaSync Plasma Monitor PlasmaSync 50XM4 PX-50XM4G2 The 5-BNC connectors are used as RGB/PC2 and 1 HD/DVD/DTV input signals supported on this system3 Compatable with HDCP Supported Signals HD/DVD2 input. Select one of them under “BNC INPUT”Supported resolution Table of Signals SupportedComputer input signals supported by this system CONFIDENTIALImportant Information CONFIDENTIALDownloaded From TV-Manual.com Manuals monitor, refer to “Model Information” For the specifications of your plasmaOperation Manual ENGLISH DEUTSCH FRANÇAIS ESPAÑOL ITALIANOWarnings and Safety Precaution PrecautionsImportant Information CONFIDENTIALContents of the Package ContentsOptions InstallationVentilation Requirements for enclosure mounting InstallationSee page E-3 CONFIDENTIALCable Management Creating a video wallInformation CONFIDENTIALHow to use the remote control Caution on when the plasma monitor is installed verticallyBattery Installation and Replacement Using the wired remote control modee POWER/STANDBY indicator q Powerr INPUT SELECT / EXIT Switches the input y VOLUME DOWN and UPC E F G H I J K Rear View/ Terminal BoardD A B 4-12q POWER ON/STANDBY Switches the power on/standby Remote Control0VOLUME + 4OFF TIMERVOLUME POWERAUTO ADJUST OFF TIMERWIDE Operations When viewing videos or digital video discsWide Screen Operation manual CONFIDENTIALWhen “PICTURE SIZE” is set to “OFF” Wide Screen Operation with FULL size screen Computer Signals Supported resolution “PICTURE SIZE” settingSPLIT SCREEN Operations Showing a couple of pictures on the screen at the same timeCONFIDENTIAL Selecting the input signals to be displayed Operations in the Picture-in-picture modeAdjusting the OSM controls 4-18Menu Operations Advanced menu mode4-19 E-154-20 Menu TreeE-16 CONFIDENTIAL4-21 Restoring the factory default settingsE-17 1 Only when AUTO PICTURE is OFF 2 RGB/PC onlyAdjusting the picture Picture Settings MenuSetting the picture mode according to the brightness of the room Setting the color temperatureMaking the Low Tone adjustments Adjusting the color to the desired levelAdjusting the colors Adjusting the white balanceImage Adjust Settings Menu Audio Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjSetting the on-screen menu Option1 Settings MenuSetting the BNC connectors Setting the RGB1 connectorResetting to the default values Setting the Input SkipSetting high definition images to the suitable screen size INPUT SKIP settingsSetting the power management for computer images Option2 Settings MenuSetting the picture to suit the movie POWER/STANDBY indicatorINVERSE Settings ORBITER settingsORBITER Function settings Setting the timeSetting the screen size for S1/S2 video input Setting the gray level for the sides of the screenSOFT FOCUS settings GRAY LEVEL settingsSetting the picture size for RGB input signals Option3 Settings MenuSetting the signal and black level for DVI signal Using the timerTo reset the program PROGRAM TIMER settingsTo reset the data Special characters in the PROGRAM TIMER screenEnabling/disabling remote control wireless transmission Setting the power on modeLoop Out setting PWR. ON MODE settingsVideo Wall setting ID number settingTo reset back to ALL ID NUMBER settingsAUTO ID settings DISP. MODE settingsIMAGE ADJUST settings P. ON DELAY settingsREPEAT TIMER settings PLE LINK settings4-35 E-31Erasing the sub screen image when there is Option4 Settings Menuno input signal ZOOM NAV settingsLanguage Settings Menu Advanced OSM Settings MenuSwitching the input source quickly Setting the menu modeSetting the video signal format Color System Settings MenuChecking the frequencies, polarities of input signals, and resolution Video signal formatsDVI-D 24-pin connector Digital mini D-Sub 15-pin connector AnalogType of connector D-Sub 9-pin male External ControlSymptom Troubleshooting4-40 Checks