NEC XT4100 11 10 9 8 7 5 4 2, 136

E – 3

LENS SHIFT ZOOM MENU SELECT

-

+

ENTER

ON

INDICATOR POWER

STATUS

ON/OFF

OFF

CANCEL

FOCUS

11 10 9 8 7 5 4 2136

1. Power Button

Press to turn the projector on when the projector is in the standby con-

dition (Main Power switch must be on and the POWER indicator lit or-

ange). Press and hold for 2 seconds to turn off the projector.

2. Power Indicator

When this indicator is green, the projector is on; when the indicator is

orange, it is in standby mode.

NOTE: After the projector is turned off, the indicator "--" flashes for three min-

utes to show that the cooling fan is working.

Do not turn off the main power during that time. After "--" stops flashing, the

POWER indicator will change to a steady orange glow and the projector will be

in the stand-by mode.

3. Status Indicator

When the On Timer is set and the projector is in the standby mode, the

Status indicator flashes green to show that the On Timer program is

active.

4. Two Digit Display

During normal operation the current projector ID (address) is shown in

this two digit display. In the ev ent of an error, a projector error code will

be displayed. The display can be turned off using the ON/OFF Switch to

the left of the display.

5. Enter Button

Executes your menu selection and activates items selected from the

menu. When the slidebar or dialog box is displayed:

Pressing this button confirms adjustments/setting and returns to the

previous menu display.

6. Cancel Button

Press this button to exit the menu. Press this button to return the adjust-

ments to the last condition while you are in the adjustment or setting

menu.

7. Select (Up/Down/Left/Right) Button

Up/Down: Use these buttons to select the menu of the item you wish to

adjust.

Left/Right: Use these buttons to change the level of a selected menu

item.

8. Menu Button

Displays the main menu for operation.

9. Zoom Button

Zoom the lens in and out.

10. Focus Button

Adjust the lens focus.

11. Lens Shift Button

Adjust the lens offset by shifting the projected image position horizon-

tally and vertically.

Remote sensor

Controls

Contents

Main Page CAUTION ATTENTION DOC compliance Notice DOC avis de conformation E iii Important Safeguards Installation To Dealer or Installer: Power Supply Cleaning Recommandations importantes Installation A lattention du revendeur ou de linstallateur: Alimentation ATTENTION LIMITED WARRANTY HOW LONG IS THE WARRANTY WHO IS PROTECTED WHAT IS COVERED AND WHAT IS NOT COVERED WHAT NEC WILL COVER TABLE OF CONTENTS INTRODUCTION 1. PART NAMES AND FUNCTIONS 2. INSTALLATION 3. SETUP INTRODUCTION Introduction to the XT5100/XT4100 Projector E 2 1. Part Names and Functions E 3 + - 11 10 9 8 7 5 4 2 Controls 136 E 4 Terminal Panel NOTE: This projector is compatible with the ISS-6020 Switcher. NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modes for the ISS-6020 switcher. NOTE: This terminal accepts component signal only. E 5 Page E 7 - NOTE: This is also considered the LENS SHUTTER. Remote Control Precautions Remote Control Battery Installation 2. INSTALLATION NOTE: Distances may vary +/- 5%. Table of Throw Distances and Screen Sizes for Optional Lenses Throw Distance Screen Size and Projection Distance Lens Shift Adjustable Range Maximum Possible Range for TL-1ZH/TL-1Z, TL-2Z and TL-4Z Fixed Lens TL-08SF E 10 Pulling Out the Handles Pull out the handle until it clicks into place. Retracting the Handles 1) Push the lever to unlock and 2) retract the handle. Selecting A Location WARNING 3. SETUP + Connecting the Power Cable and Turn- ing on the Projector - Using the Power Cable Stopper Set up the projector + - E 13 Keystone Setting up for Double or Triple Stacking in Link Mode E 14 E 15 Projector Orientation E 16 When used in standalone operation Connecting Your PC Or Macintosh Computer 4. CONNECTIONS Connecting Your VCR Or Laser Disc Player PC control ISS-6020 Switcher Wired remote control PC Document camera DVD player PC / Workstation DVD player VCR LD player Document camera When Used with One Switcher (ISS-6020/ISS-6020G) E 18 When Used with Two or More Switchers (100 Inputs) How to make connections: Page E 20 REMOTE 1 Connector E 21 When used in stand alone operation. E 22 Operating Multiple Projectors with Remote Control E 23 Using the RGB DIGITAL connectors Connection for Triple Stacking in Link Mode Link Mode Connecting a PC with the RGB digital connector E 24 5. OPERATION General Controls 1. Turn On The Projector 2. Select The Computer Or Video Source 3. Adjust The Image E 25 A List of Direct Key Combinations E 26 Menu Tree E 27 E 28 Menu windows or dialog boxes typically have the following elements: Menu Elements E 29 Menu Descriptions & Functions Source Select NOTE: Existing direct key settings are overwritten with new settings. Entry List Swicher E 30 Adjust (Source) White Balance Image E 31 Video Adj E 32 NOTE: The Color Matrix feature is available for component video signal only. Option Adj E 33 Lens Memory Ref Adj Keystone Switcher E 34 Projector Options Timer Factory Default Lamp NOTE: All the items in "Adjust (Source)" can be reset. E 35 Menu E 36 Setup ". This should be "75 NOTE: The default setting is "75 NOTE: These S-Video signals are not used in the US. E 37 NOTE: This setting becomes effective only after the projector is restarted. Link Mode Switcher Control PC Card Files Help E 39 Test Pattern E 40 6. SPECIFICATIONS Optical Electrical E 41 Mechanical E 42 7. Optional Accessories E 43 8. Compatible Input Signal List Compatible Input Signal List List of Menu Items Available on Link Mode E 44 9. E 45 Appendix Dimensions E 46 Tips on Adjusting Focus for Lens Memory Function