NEC XT4100 E 41, Mechanical

E – 41

External Control RS232C (1) D-sub 9 pin

Contact Closure

Switcher (2) D-sub 15 pin In/Out

Addressable Remote Control (wired / wireless)

Power Requirement 100-120 / 200-240 VAC, 50/60Hz

Input Current 11 A / 7.3 A

Power Consumption 1.0 kW / 1.5 KW

Mechanical

Installation Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear

Stacking: Up to 3 projectors can be gravity stacked

Dimensions 22.0" (W) x 26.9" (D) x 11.8" (H) / 560 mm (W) x 682 mm (D) x 300 mm (H)

with lens hood and foot (not including handle, stacking pad and protrusions)

Net Weight 95 lb (43Kg) (without lens)

Environment Operational Temperature 40˚ to 95˚F / 5˚ to 35˚C,

Humidity: 20-80% non-condensing

Storage: 14˚ to 122˚F / -10˚ to 50˚C

Humidity: 20-80% non-condensing

Regulations USA UL 1950 FCC Class A

Canada CSA950 ( C-UL )

Europe EN60950 EN55022 Class A EN55024 EN61000-3-2 EN61000-3-3

Japan J60950 VCCI

Oceania EN60950 AS/NZS3548 Class A

Asia EN60950 CISPR22 Class A

*1: Permissible deviation for RGB convergence (Pixel deviation) is 1/2 pixel or less at center; 1 pixel or less around the perimeter (when projection

upward angle is 0˚).

*2: When using the zoom lens, it is recommended that the projector is positioned at an angle of from -15 to +15 degrees from the horizontal.

Specifications are subject to change without notice.

Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.

Contents

Main Page CAUTION ATTENTION DOC compliance Notice DOC avis de conformation E iii Important Safeguards Installation To Dealer or Installer: Power Supply Cleaning Recommandations importantes Installation A lattention du revendeur ou de linstallateur: Alimentation ATTENTION LIMITED WARRANTY HOW LONG IS THE WARRANTY WHO IS PROTECTED WHAT IS COVERED AND WHAT IS NOT COVERED WHAT NEC WILL COVER TABLE OF CONTENTS INTRODUCTION 1. PART NAMES AND FUNCTIONS 2. INSTALLATION 3. SETUP INTRODUCTION Introduction to the XT5100/XT4100 Projector E 2 1. Part Names and Functions E 3 + - 11 10 9 8 7 5 4 2 Controls 136 E 4 Terminal Panel NOTE: This projector is compatible with the ISS-6020 Switcher. NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modes for the ISS-6020 switcher. NOTE: This terminal accepts component signal only. E 5 Page E 7 - NOTE: This is also considered the LENS SHUTTER. Remote Control Precautions Remote Control Battery Installation 2. INSTALLATION NOTE: Distances may vary +/- 5%. Table of Throw Distances and Screen Sizes for Optional Lenses Throw Distance Screen Size and Projection Distance Lens Shift Adjustable Range Maximum Possible Range for TL-1ZH/TL-1Z, TL-2Z and TL-4Z Fixed Lens TL-08SF E 10 Pulling Out the Handles Pull out the handle until it clicks into place. Retracting the Handles 1) Push the lever to unlock and 2) retract the handle. Selecting A Location WARNING 3. SETUP + Connecting the Power Cable and Turn- ing on the Projector - Using the Power Cable Stopper Set up the projector + - E 13 Keystone Setting up for Double or Triple Stacking in Link Mode E 14 E 15 Projector Orientation E 16 When used in standalone operation Connecting Your PC Or Macintosh Computer 4. CONNECTIONS Connecting Your VCR Or Laser Disc Player PC control ISS-6020 Switcher Wired remote control PC Document camera DVD player PC / Workstation DVD player VCR LD player Document camera When Used with One Switcher (ISS-6020/ISS-6020G) E 18 When Used with Two or More Switchers (100 Inputs) How to make connections: Page E 20 REMOTE 1 Connector E 21 When used in stand alone operation. E 22 Operating Multiple Projectors with Remote Control E 23 Using the RGB DIGITAL connectors Connection for Triple Stacking in Link Mode Link Mode Connecting a PC with the RGB digital connector E 24 5. OPERATION General Controls 1. Turn On The Projector 2. Select The Computer Or Video Source 3. Adjust The Image E 25 A List of Direct Key Combinations E 26 Menu Tree E 27 E 28 Menu windows or dialog boxes typically have the following elements: Menu Elements E 29 Menu Descriptions & Functions Source Select NOTE: Existing direct key settings are overwritten with new settings. Entry List Swicher E 30 Adjust (Source) White Balance Image E 31 Video Adj E 32 NOTE: The Color Matrix feature is available for component video signal only. Option Adj E 33 Lens Memory Ref Adj Keystone Switcher E 34 Projector Options Timer Factory Default Lamp NOTE: All the items in "Adjust (Source)" can be reset. E 35 Menu E 36 Setup ". This should be "75 NOTE: The default setting is "75 NOTE: These S-Video signals are not used in the US. E 37 NOTE: This setting becomes effective only after the projector is restarted. Link Mode Switcher Control PC Card Files Help E 39 Test Pattern E 40 6. SPECIFICATIONS Optical Electrical E 41 Mechanical E 42 7. Optional Accessories E 43 8. Compatible Input Signal List Compatible Input Signal List List of Menu Items Available on Link Mode E 44 9. E 45 Appendix Dimensions E 46 Tips on Adjusting Focus for Lens Memory Function