Manuals / Brands / Computer Equipment / Projector / NEC / Computer Equipment / Projector

NEC XT4100 When Used with Two or More Switchers (100 Inputs)

1 54

Download 54 pages, 921.43 Kb

E – 18

When Used with Two or More Switchers(100 Inputs)

Up to 100 inputs can be accepted using the NEC ISS-6020 Switcher.

How to make connections:

1.Connect the REMOTE 1 terminal of the master Switcher to the RE-

MOTE 1 of the projector using the optional control cable (15p-15p/

CTL-6010).

2.Next connect the REMOTE 2 terminal of the master Switcher to the

REMOTE 1 terminal of the first slave Switcher using the same op-

tional control cable as mentioned above. Third, connect the REMOTE

2 terminal of the first slave to the REMOTE 1 of the second slave,

and the REMOTE 2 terminal of the second slave to the REMOTE 1

terminal of the third slave (— and the REMOTE 2 of the ninth slave to

the REMOTE 1 of the tenth slave). Connect all the Switchers with

optional control cables.

NOTE:

•Be sure to set all the slide switches (S8603) of the Switcher to RS-422 posi-

tions. Set the one on the last slave Switcher to the appropriate position to

match the connected equipment such as a personal computer. (RS-422/RS-

232C for PC control of projector)

•Set the DIP switch S8601 of the Switcher.

To use the projector with the Switcher ISS-6020 in the Switcher Control mode,

* When connecting with the VIDEO INPUT MODULE (6020-VID), set the VIDEO MODE select switch (S3001) to "8". The VIDEO MODE select

switch is located on the VIDEO INPUT MODULE (6020-VID).

NOTE: While in the Switcher Control mode, a video standard is selected at the projector.

If you set the VIDEO MODE select switch (S3001) to "8" with the QUAD DECODER installed in the Switcher ISS-6020, the image will not be displayed correctly.

In that case, first remove the QUAD DECODER from the Switcher ISS-6020.

For more details, contact your dealer.

OPTION (PC)

MASTER

SWITCHER

REMOTE

CONTROL

OPTION

(PC)

SLAVE 1

SLAVE 2

SLAVE 10

10 inputs

10 inputs

10 inputs

Signal Switcher

Signal

REMOTE 1

REMOTE 2

Signal

REMOTE 1

REMOTE 2

SLAVE 3

SLAVE 9 Signal

REMOTE 1

REMOTE 2

REMOTE 2

To SLOT 1

To SLOT 2

To SLOT 10

To REMOTE 2

REMOTE 1

Signal (Input 1)

REMOTE

Projector

NOTE: The optional remote control RC-6320 for ISS-6020 will not work cor-

rectly in the SW Level 1 or 2 mode.

REMOTE 1

Contents

Main Page CAUTION ATTENTION DOC compliance Notice DOC avis de conformation E iii Important Safeguards Installation To Dealer or Installer: Power Supply Cleaning Recommandations importantes Installation A lattention du revendeur ou de linstallateur: Alimentation ATTENTION LIMITED WARRANTY HOW LONG IS THE WARRANTY WHO IS PROTECTED WHAT IS COVERED AND WHAT IS NOT COVERED WHAT NEC WILL COVER TABLE OF CONTENTS INTRODUCTION 1. PART NAMES AND FUNCTIONS 2. INSTALLATION 3. SETUP INTRODUCTION Introduction to the XT5100/XT4100 Projector E 2 1. Part Names and Functions E 3 + - 11 10 9 8 7 5 4 2 Controls 136 E 4 Terminal Panel NOTE: This projector is compatible with the ISS-6020 Switcher. NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modes for the ISS-6020 switcher. NOTE: This terminal accepts component signal only. E 5 Page E 7 - NOTE: This is also considered the LENS SHUTTER. Remote Control Precautions Remote Control Battery Installation 2. INSTALLATION NOTE: Distances may vary +/- 5%. Table of Throw Distances and Screen Sizes for Optional Lenses Throw Distance Screen Size and Projection Distance Lens Shift Adjustable Range Maximum Possible Range for TL-1ZH/TL-1Z, TL-2Z and TL-4Z Fixed Lens TL-08SF E 10 Pulling Out the Handles Pull out the handle until it clicks into place. Retracting the Handles 1) Push the lever to unlock and 2) retract the handle. Selecting A Location WARNING 3. SETUP + Connecting the Power Cable and Turn- ing on the Projector - Using the Power Cable Stopper Set up the projector + - E 13 Keystone Setting up for Double or Triple Stacking in Link Mode E 14 E 15 Projector Orientation E 16 When used in standalone operation Connecting Your PC Or Macintosh Computer 4. CONNECTIONS Connecting Your VCR Or Laser Disc Player PC control ISS-6020 Switcher Wired remote control PC Document camera DVD player PC / Workstation DVD player VCR LD player Document camera When Used with One Switcher (ISS-6020/ISS-6020G) E 18 When Used with Two or More Switchers (100 Inputs) How to make connections: Page E 20 REMOTE 1 Connector E 21 When used in stand alone operation. E 22 Operating Multiple Projectors with Remote Control E 23 Using the RGB DIGITAL connectors Connection for Triple Stacking in Link Mode Link Mode Connecting a PC with the RGB digital connector E 24 5. OPERATION General Controls 1. Turn On The Projector 2. Select The Computer Or Video Source 3. Adjust The Image E 25 A List of Direct Key Combinations E 26 Menu Tree E 27 E 28 Menu windows or dialog boxes typically have the following elements: Menu Elements E 29 Menu Descriptions & Functions Source Select NOTE: Existing direct key settings are overwritten with new settings. Entry List Swicher E 30 Adjust (Source) White Balance Image E 31 Video Adj E 32 NOTE: The Color Matrix feature is available for component video signal only. Option Adj E 33 Lens Memory Ref Adj Keystone Switcher E 34 Projector Options Timer Factory Default Lamp NOTE: All the items in "Adjust (Source)" can be reset. E 35 Menu E 36 Setup ". This should be "75 NOTE: The default setting is "75 NOTE: These S-Video signals are not used in the US. E 37 NOTE: This setting becomes effective only after the projector is restarted. Link Mode Switcher Control PC Card Files Help E 39 Test Pattern E 40 6. SPECIFICATIONS Optical Electrical E 41 Mechanical E 42 7. Optional Accessories E 43 8. Compatible Input Signal List Compatible Input Signal List List of Menu Items Available on Link Mode E 44 9. E 45 Appendix Dimensions E 46 Tips on Adjusting Focus for Lens Memory Function