NEC XT4100 Menu Tree

E – 26

Menu Tree

NTSC, Graphics, Graphics/NTSC, PAL/SECAM2.8,

PAL/SECAM, Natural 1/Natural 2

Advanced Menu

Source Select

Adjust (Source)

Ref Adj

Factory Default

Projector Options

PC Card Files

Help

Test Pattern

RGB1

RGB2

RGB3

Component (YCbCr)

Video1

Video2

S-Video1

S-Video2

RGB (DIGITAL)

SDI

Entry List

Switcher

Entry List

When Switcher Control is

turned on:

Stand alone

Brightness

Contrast

Saturation

Color

Hue

Sharpness

V-Aperture

Gamma Correction

Color Temperature

Brightness

Contrast

Signal Level

Pixel Adjust

Position

Aspect Ratio

Resolution

Overscan

Video Filter

Blanking

Noise Reduction

Color Matrix

Y/C Delay

Telecine

Motion Select

Motion Level

YTR Adjustment

CTR Adjustment

Clamp Timing

Sync Protection

VD Delay

Gain

Volume

Reference / Custom

Picture

White Balance

Image

Video Adj

Option Adj

Lens Memory

Switcher

Brightness R/G/B

Contrast R/G/B

Red/Green/Blue or Y/Cb/Cr

Clock / Phase

Horizontal / Vertical

Input Signal 1.33:1 / 1.78:1 / 1.85:1 / 2.35:1

Display Area 1.33:1 / 1.78:1 / 1.85:1 / 2.35:1

Auto / Native

0% / 5% / 10% / 25%

Top / Bottom / Left / Right

Luminance Off / Low / Medium / High

Chrominance Off / Low / Medium / High

Select Color Matrix HDTV / SDTV

Delect Color Matrix Type B-Y/R-Y, U/V, Cb/Cr

Pb/Pr, IVX

Auto / Off

Still / Adaptive

Auto / Tri-Sync / Front Porch / Adjust

Upper / Lower

0 / 2.5u / 5u / 10u

Red / Green / Blue

Contents

Main Page CAUTION ATTENTION DOC compliance Notice DOC avis de conformation E iii Important Safeguards Installation To Dealer or Installer: Power Supply Cleaning Recommandations importantes Installation A lattention du revendeur ou de linstallateur: Alimentation ATTENTION LIMITED WARRANTY HOW LONG IS THE WARRANTY WHO IS PROTECTED WHAT IS COVERED AND WHAT IS NOT COVERED WHAT NEC WILL COVER TABLE OF CONTENTS INTRODUCTION 1. PART NAMES AND FUNCTIONS 2. INSTALLATION 3. SETUP INTRODUCTION Introduction to the XT5100/XT4100 Projector E 2 1. Part Names and Functions E 3 + - 11 10 9 8 7 5 4 2 Controls 136 E 4 Terminal Panel NOTE: This projector is compatible with the ISS-6020 Switcher. NOTE: The INPUT 2 terminal does not support SW1 Level and SW2 Level modes for the ISS-6020 switcher. NOTE: This terminal accepts component signal only. E 5 Page E 7 - NOTE: This is also considered the LENS SHUTTER. Remote Control Precautions Remote Control Battery Installation 2. INSTALLATION NOTE: Distances may vary +/- 5%. Table of Throw Distances and Screen Sizes for Optional Lenses Throw Distance Screen Size and Projection Distance Lens Shift Adjustable Range Maximum Possible Range for TL-1ZH/TL-1Z, TL-2Z and TL-4Z Fixed Lens TL-08SF E 10 Pulling Out the Handles Pull out the handle until it clicks into place. Retracting the Handles 1) Push the lever to unlock and 2) retract the handle. Selecting A Location WARNING 3. SETUP + Connecting the Power Cable and Turn- ing on the Projector - Using the Power Cable Stopper Set up the projector + - E 13 Keystone Setting up for Double or Triple Stacking in Link Mode E 14 E 15 Projector Orientation E 16 When used in standalone operation Connecting Your PC Or Macintosh Computer 4. CONNECTIONS Connecting Your VCR Or Laser Disc Player PC control ISS-6020 Switcher Wired remote control PC Document camera DVD player PC / Workstation DVD player VCR LD player Document camera When Used with One Switcher (ISS-6020/ISS-6020G) E 18 When Used with Two or More Switchers (100 Inputs) How to make connections: Page E 20 REMOTE 1 Connector E 21 When used in stand alone operation. E 22 Operating Multiple Projectors with Remote Control E 23 Using the RGB DIGITAL connectors Connection for Triple Stacking in Link Mode Link Mode Connecting a PC with the RGB digital connector E 24 5. OPERATION General Controls 1. Turn On The Projector 2. Select The Computer Or Video Source 3. Adjust The Image E 25 A List of Direct Key Combinations E 26 Menu Tree E 27 E 28 Menu windows or dialog boxes typically have the following elements: Menu Elements E 29 Menu Descriptions & Functions Source Select NOTE: Existing direct key settings are overwritten with new settings. Entry List Swicher E 30 Adjust (Source) White Balance Image E 31 Video Adj E 32 NOTE: The Color Matrix feature is available for component video signal only. Option Adj E 33 Lens Memory Ref Adj Keystone Switcher E 34 Projector Options Timer Factory Default Lamp NOTE: All the items in "Adjust (Source)" can be reset. E 35 Menu E 36 Setup ". This should be "75 NOTE: The default setting is "75 NOTE: These S-Video signals are not used in the US. E 37 NOTE: This setting becomes effective only after the projector is restarted. Link Mode Switcher Control PC Card Files Help E 39 Test Pattern E 40 6. SPECIFICATIONS Optical Electrical E 41 Mechanical E 42 7. Optional Accessories E 43 8. Compatible Input Signal List Compatible Input Signal List List of Menu Items Available on Link Mode E 44 9. E 45 Appendix Dimensions E 46 Tips on Adjusting Focus for Lens Memory Function