)NSTALLATION 'UIDE
I L
7000 Series Managed Switch (7200, 7300, 7300S)
Start Here
Before you begin installation of your switch, check the Package Contents listed in the Hardware Installation Guide that supports your switch (7200, 7300, or 7300S) on your Resource CD. If any item is missing or damaged, contact your place of purchase.
Other documentation available on your Resource CD for your switch are the 7000 Series Managed Switch Administration Guide, and a Command Line Interface Reference Manual for each switch series (7200, 7300, or 7300S).
Follow these quick steps to install your switch. You can also consult the full Hardware Installation Guide on the Resource CD.
Set Up the Switch
Prepare the site so that the mounting, access, power source, and environmental requirements are met. If you have any questions about these requirements, see the Hardware Installation Guide for your switch on your Resource CD.
1.INSTALL THE SWITCH USING ONE OF THE FOLLOWING METHODS
a.On a flat surface: Put one of the rubber footpads that came with the switch on each of the four concave spaces on the bottom of the switch.
b.In a Rack: Use the
2.APPLY AC POWER
When you apply power, the power LED can display the following behavior:
• The power LED will blink yellow as it conducts a
• If the power LED does not light, check that the power cable is plugged in correctly and that the power source is good. If this does not resolve the problem, see “Troubleshooting” in the Hardware Installation Guide on the Resource CD.
3.CONNECT DEVICES TO THE SWITCH
•Use Category 5 (Cat5) cable to connect between network ports at speeds of 100Mbps or less.
•Use Category 5e (Cat5e) for 1000Mbps networking speed.
Fiber SFP modules are shipped separately. If you need instructions on installing an SFP module, please refer to the Hardware Installation Guide on the Resource CD.
Note: In the room housing the switch, ensure that the ambient temperature does not exceed the specified operating temperature and that the environment is free of water condensation.
Perform the Initial Configuration
This switch can be managed through its Web interface, or by using the Command Line Interface (CLI) through the serial console port. This guide describes the Web method. The CLI method is also described to determine a
•PC in DHCP client mode without DHCP server
•PC with static IP address
•PC in DHCP client mode with DHCP server
To perform extensive CLI management, see both the CLI Reference Manual for your switch and the 7000 Series Administration Guide.
PC in DHCP Client Mode without DHCP Server
If no DHCP server is present, the switch assumes a default IP address of 169.254.100.100 and a subnet mask of 255.255.0.0. The switch is in the same subnet used by a PC NIC port when in
PC with Static IP Address
When the PC is in this mode, the switch must also be assigned a static IP address. To assign a static IP Address, access the switch from the serial console port as follows:
1.CONNECT A CONSOLE TO THE SWITCH
Using the
2.START A TERMINAL EMULATION PROGRAM (TEP)
a.Start a TEP using the appropriate method for your operating system:
•Windows users can use HyperTerminal.
•Windows Vista users should download a TEP from the Internet.
•Macintosh users can use ZTerm.
•UNIX users can use a terminal emulator such as TIP.
b.Configure the TEP to use the following settings (they are written below the connector on the switch front panel):
•Baud rate: 9,600 bps
•Data bits: 8
•Parity: none
•Stop bit: 1
•Flow control: none
c.At the command prompt User:, login to the switch using the user name admin, then press Enter. At the password prompt, press Enter again (no password is needed for initial configuration).
d.At the next command prompt, type ezconfig and press Enter.
The ezconfig utility is now running in the switch. Use it to set up your static IP address and subnet mask as shown in the following example. Make sure that the selected switch IP address is in the same subnet as that of the PCs.
