Manuals / Network Technologies / Computer Equipment / Switch

Network Technologies 900GV Accessing Online Information, Documentation Comments, Online Services

Models: 900GV

1 72

Download 72 pages 63.73 Kb

Page 11

Accessing Online Information

Accessing Online Information

Documentation Comments

If you have comments or suggestions about this document, send them to

TechWriting@cabletron.com

Online Services

To locate product-specific information, refer to one of the following World Wide Web sites:

Americas:	http://www.networks.digital.com
	or
	http://www.cabletron.com/
Europe	http://www.networks.europe.digital.com
Asia Pacific	http://www.networks.digital.com.au

xi

Image 11

Network Technologies 900GV manual Accessing Online Information, Documentation Comments, Online Services

Contents

Revision Information Digital VNswitch 900GV Installation and ConfigurationAchtung Contents Installing the Digital VNswitch 900GV Removing the Cables, Connector and Module Page Intended Audience PrefaceOverview Purpose of the ManualSection Description OrganizationTitle and Order Description Associated DocumentsBoldface ConventionsConvention Description Documentation Comments Accessing Online InformationOnline Services Page Achtung SafetyThis action deletes all configured settings and replaces Topic Chapter Product IntroductionThis Chapter What is the Digital VNswitch 900GV? Hot Swap FeaturesConfiguration and Management Ethernet BridgingMibs Vlan Secure Domains Introduction Chapter Installing the Digital VNswitch 900GVIcon Name Description Front Panel LEDs and ConnectorsModule Components Front Panel ComponentsFRU LED Name Description Back Panel ComponentsBack Panel Components Task 1 Compare the Power Ratings How to Install the ModuleStep Action Task 2 Seat the ModuleStage Description Task 3 Verify Initial LED OperationIf… Then… 5LDM Port Cable Connection Task 4 Connect the LDM Port Cable6GBIC Connection Task 5 Connect the Gbic ConnectorFiber Size Fiber Bandwidth Distance Task 6 Connect the Duplex SC CablesLong Wave Length Blue HP 5611 Overview Chapter Installing the Setup Port CableIf the setup port device is… Use this cable… Setup Port Signaling StandardsSetup Port Device Cabling Item Description Connecting to the Setup Port1Setup Port Cabling Components Chapter Configuring the Module in a Digital MultiSwitchStep Action Assigning an IP AddressRedirect Mode Digital MultiSwitch 900 Installation MenuStart Redirect Mode Using Menus to Configure the Module Restart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration Configure IPTopic SET Smnp READ/WRITE Community Set Snmp Read/Write CommunityADD Snmp Trap Addresses Add Snmp Trap AddressesLine Field Description Delete Snmp Trap Addresses Delete Snmp Trap AddressesSet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSet Out-of-Band Interface IP Address OUT-OF-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Options from the VNswitch 900GV Installation Menu Product-Specific Options VNswitch 900GVPRODUCT-SPECIFIC Options Product-Specific Options MultiSwitchPage Removing the Cables, Connector and Module 1Removing the LDM Port Cable Removing the CablesGbic Removal Removing the Gbic Card3Unseating the Module Unseating the ModuleThis Appendix Appendix a Problem SolvingEvent Description Normal Power-UpOff On Green On Yellow Flashing LED DescriptionsTable A-1Module LED States LED Name Off On Green On Yellow Flashing Problem Solving Using LEDs Symptom Probable Cause Corrective Action Overview Appendix B Connector Pin Assignments and Adapters10BaseT Port 8-pin MJ Straight-through Connector Connectors and Pin AssignmentsH8571-J Adapter AdaptersFigure B-3 H8575-A Adapter H8575-A AdapterOverview Appendix C Product SpecificationsTable C-1 Product Specifications Parameter Product SpecificationsTable C-3German Acoustical Specifications Acoustical SpecificationsTable C-2Acoustical Specifications Table C-4 Connectors Quantity Connectors