Manuals / Network Technologies / Computer Equipment / Switch

Network Technologies 900GV manual Removing the Cables, Connector and Module

Models: 900GV

1 72

Download 72 pages 63.73 Kb

Page 55

Chapter 5

Removing the Cables, Connector and Module

Overview

Introduction

This chapter describes how to remove the DIGITAL VNswitch 900GV module, cables and connectors from a DIGITAL MultiSwitch 900 chassis.

In This Chapter

This chapter contains the following topics:

Topic	Page

Removing the Cables	5-2
Removing the GBIC Card	5-3
Unseating the Module	5-4

Removing the Cables, Connector and Module 5-1

Image 55

Network Technologies 900GV manual Removing the Cables, Connector and Module

Contents

Revision Information Digital VNswitch 900GV Installation and ConfigurationAchtung Contents Installing the Digital VNswitch 900GV Removing the Cables, Connector and Module Page Intended Audience PrefaceOverview Purpose of the ManualSection Description OrganizationTitle and Order Description Associated DocumentsConvention Description ConventionsBoldface Online Services Accessing Online InformationDocumentation Comments Page Achtung SafetyThis action deletes all configured settings and replaces This Chapter Chapter Product IntroductionTopic What is the Digital VNswitch 900GV? Configuration and Management FeaturesHot Swap Ethernet BridgingMibs Vlan Secure Domains Introduction Chapter Installing the Digital VNswitch 900GVIcon Name Description Front Panel LEDs and ConnectorsModule Components Front Panel ComponentsFRU LED Back Panel Components Back Panel ComponentsName Description Task 1 Compare the Power Ratings How to Install the ModuleStep Action Task 2 Seat the ModuleIf… Then… Task 3 Verify Initial LED OperationStage Description 5LDM Port Cable Connection Task 4 Connect the LDM Port Cable6GBIC Connection Task 5 Connect the Gbic ConnectorLong Wave Length Blue HP 5611 Task 6 Connect the Duplex SC CablesFiber Size Fiber Bandwidth Distance Overview Chapter Installing the Setup Port CableSetup Port Device Cabling Setup Port Signaling StandardsIf the setup port device is… Use this cable… Item Description Connecting to the Setup Port1Setup Port Cabling Components Chapter Configuring the Module in a Digital MultiSwitchStep Action Assigning an IP AddressRedirect Mode Digital MultiSwitch 900 Installation MenuStart Redirect Mode Using Menus to Configure the Module Restart with Factory Defaults Restart with Current Settings Restart with Current SettingsShow Current Settings IP Configuration Configure IPTopic SET Smnp READ/WRITE Community Set Snmp Read/Write CommunityLine Field Description Add Snmp Trap AddressesADD Snmp Trap Addresses Delete Snmp Trap Addresses Delete Snmp Trap AddressesSet In-Band Interface IP Address IN-BAND Interface IP Address ConfigurationSet Out-of-Band Interface IP Address OUT-OF-BAND Interface IP Address ConfigurationSET IN-BAND Interface Default Gateway Address Set Default GatewayGo to Local Console Options from the VNswitch 900GV Installation Menu Product-Specific Options VNswitch 900GVPRODUCT-SPECIFIC Options Product-Specific Options MultiSwitchPage Removing the Cables, Connector and Module 1Removing the LDM Port Cable Removing the CablesGbic Removal Removing the Gbic Card3Unseating the Module Unseating the ModuleThis Appendix Appendix a Problem SolvingEvent Description Normal Power-UpTable A-1Module LED States LED DescriptionsOff On Green On Yellow Flashing LED Name Off On Green On Yellow Flashing Problem Solving Using LEDs Symptom Probable Cause Corrective Action Overview Appendix B Connector Pin Assignments and Adapters10BaseT Port 8-pin MJ Straight-through Connector Connectors and Pin AssignmentsH8571-J Adapter AdaptersFigure B-3 H8575-A Adapter H8575-A AdapterOverview Appendix C Product SpecificationsTable C-1 Product Specifications Parameter Product SpecificationsTable C-2Acoustical Specifications Acoustical SpecificationsTable C-3German Acoustical Specifications Table C-4 Connectors Quantity Connectors