7. Appendix

￿Troubleshooting

This section helps you resolve problems you may encounter while setting up or using the projector.

Indicator Messages

Power Indicator

 

Indicator Condition

 

Projector Condition

Note

 

Off

 

The main power is off

 

 

 

 

 

 

 

Blinking light

Green

 

0.5 sec On,

The projector is getting ready to turn on.

Wait for a moment.

 

 

 

0.5 sec Off

 

 

 

 

 

 

 

 

 

 

 

 

 

2.5 sec On,

Off Timer is enabled.

 

 

 

0.5 sec Off

 

 

 

 

 

 

 

 

 

 

 

Orange

 

0.5 sec On,

The projector is cooling down.

Wait for a moment.

 

 

 

0.5 sec Off

 

 

 

 

 

 

 

 

 

 

Steady light

Green

 

The projector is turned on.

 

 

 

 

 

 

 

Orange

 

The projector is in Standby.

 

 

 

 

 

 

 

Status Indicator

 

 

 

 

 

 

 

 

 

 

 

Indicator Condition

 

Projector Condition

Note

 

Off

 

Normal

 

 

 

 

 

 

Blinking light

Red

 

1 cycle (0.5 sec On,

Lamp cover error or lamp housing error

Replace the lamp cover or lamp

 

 

 

2.5 sec Off)

 

housing correctly.

 

 

 

2 cycle (0.5 sec On,

Temperature error

The projector is overheated. Move

 

 

 

0.5 sec Off)

 

the projector to a cooler location.

 

 

 

4 cycle (0.5 sec On,

Fan error

Fans will not work correctly.

 

 

 

0.5 sec Off)

 

 

 

 

 

 

6 cycle (0.5 sec On,

Lamp error

Lamp fails to light. Wait a full

 

 

 

0.5 sec Off)

 

minute and then turn on again.

 

 

 

 

 

 

 

 

Green

 

Re-firing the lamp (The projector is cool-

The projector is re-firing.

 

 

 

 

ing down.)

Wait for a moment.

Steady light

Orange

 

Cabinet button is locked

You have pressed cabinet button

 

 

 

 

 

when Cabinet Button is locked.

 

 

 

 

 

 

Lamp Indicator

 

 

 

 

 

 

 

 

 

 

 

Indicator Condition

 

Projector Condition

Note

 

Off

 

Normal

 

 

 

 

 

 

Blinking light

Red

 

Lamp has reached its end of life. Lamp

Replace the lamp.

 

 

 

 

replacement message will be displayed.

 

 

Steady light

Red

 

Lamp has been used beyond its limit. The

Replace the lamp.

 

 

 

 

projector will not turn on until the lamp is

 

 

 

 

 

 

replaced.

 

 

 

Green

 

Lamp mode is set to Eco mode

 

 

 

 

 

 

 

Over-Temperature Protection

If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the STATUS indicator blinking (2-cycle On and Off.)

Should this happen, do the following:

Unplug the power cable after the cooling fans stop.

Move the projector to a cooler location if the room where you are presenting is particularly too warm.

Clean the ventilation holes if they are clogged with dust.

Wait about 60 minutes until the inside of the projector becomes cool enough.

55