Nilfisk-ALTO 05210F, 05210G, 05211F, 05220F, 05220G, 05221F, 05230F, 05231F WARNING:, WARNING:

Nilﬁ sk ALTO Operator's Manual - SCRUBTEC 770 / 784 / 795 FORM NO. 70935A - 7 -

PROCEDURES FOR TRANSPORTING

How To Put The Machine In A Van Or Truck

WARNING:

The machine is heavy. Make sure you use two able persons to assist the machine in climbing the ramp.

1. Make sure the loading ramp is at least eight (8) feet long, and strong enough to support the machine.

2. Make sure the ramp is clean and dry.

3. Put the ramp in position.

4. Remove squeegee assembly, brush housings, & brushes or pad drivers before loading.

5. Turn key switch “ON”.

6. Align the machine on a level surface ten (10) feet in front of the ramp.

7. Put the traverse speed switch in the “HI” position.

8. Press one or both forward switches.

9. Push the machine to the top of the ramp.

10. Turn the key switch “OFF”.

11. Fasten the machine to the vehicle.

How To Remove The Machine From A Van Or Truck

1. Make sure there are no obstructions in the area.

2. Make sure the unloading ramp is at least eight (8) feet long and strong enough to support the machine.

3. Make sure the ramp is clean and dry.

4. Put the ramp in position.

5. Unfasten the machine.

WARNING:

The machine is heavy. Make sure you use two able persons to assist in moving the machine down the ramp.

6. Turn the key switch “ON”.

7. Carefully and slowly, drive the machine to the top of the ramp by pressing and holding either of the forward switches and the

reverse switch.

8. Put the traverse speed switch to the mid range speed setting. As the machine begins to travel down the ramp, maintain a slow

downward speed by pressing either of the forward switches.

9. Replace squeegee assembly, brush housings, & brushes or pad drivers after the machine is unloaded and ready to use.

Contents

Main Operator's Manual Table of Contents Section II Parts and Service Manual Page Page INTRODUCTION Machine Speci cations Page PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: How To Remove The Machine From A Van Or Truck WARNING: Page SYMBOLS USED ON SCRUBTEC 770, 784, 795 71018A 71015A 71014A 71017A Page Page MACHINE CONTROL PANEL 770L, 784L & 795L Page DISPLAY SCREENS FOR SCRUBTEC 770L, 784L, 795L EN MACHINE CONTROLS & FEATURES CAUTION! HOW TO PREPARE THE MACHINE FOR OPERA- TION HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers BA Page Page Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and recovery tank before doing any maintenance. Keep all fasteners tight. BA Page Page Page HOW TO CORRECT PROBLEMS IN THE MACHINE SCRUBTEC 770L / 784L / 795L WB Common Error Codes Page Parts and Service Manual Page Nil sk ALTO NOTE 1: Only used on the following models: 05210G, 05220G. Solution Tank Assembly 12/09 Item Ref. No. Qty Description Page Nil sk ALTO Recovery Tank Assembly 12/09 Item Ref. No. Qty Description Page Page Page SCRUBTEC 770L / 784L / 795L Control Panel Assembly 12/09 Item Ref. No. Qty Description Nil sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / Solo Speed Controller 12/09 Item Ref. No. Qty Description Page Item Ref. No. Qty Description Nil sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / I-Drive Speed Controller 12/09 Page Squeegee Swing Arm Assembly 12/09 Item Ref. No. Qty Description Page SCRUBTEC 770 / 784 Squeegee Assembly 12/09 Item Ref. No. Qty Description Page Item Ref. No. Qty Description SCRUBTEC 795 Squeegee Assembly 12/09 Nil sk ALTO Traverse System Assembly 2/05 Nil sk ALTO Traverse System Assembly 2/05 Item Ref. No. Qty Description Nil sk ALTO Brush Head Assembly Drawing 2/05 Nil sk ALTO Brush Head Assembly Parts List 11/07 Item Ref. No. Qty Description Item Ref. No. Qty Description Nil sk ALTO Brush Motor #45036A 2/05 Item Ref. No. Qty Description Page Nil sk ALTO Imperial Transaxle Parts 2/05 PN 59116A Item Ref. No. Qty Description Nil sk ALTO Imperial Transaxle Parts 2/05 PN 59116A ACCESSORIES BRUSHES: PAD DRIVERS: Page Page Page Page Page Page Nil sk ALTO reserves the right to make changes or improvements to its machine without notice. Always use genuine Nil sk ALTO Parts for repair. Nil sk ALTO LIMITED U.S. WARRANTY 3 YEARS FOR PARTS AND 1 YEAR FOR SERVICE LABOR (See exceptions below) BATTERY WARRANTY Nil sk ALTO: POLYDUR AUTOMATIC SCRUBBER SOLUTION AND RECOVERY TANK EIGHT-YEAR U.S. GUARANTEE