Nilfisk-ALTO 05210F, 05210G, 05211F, 05220F, 05220G, 05221F, 05230F, 05231F SYMBOLS USED ON SCRUBTEC 770, 784, 795

Nilﬁ sk ALTO Operator's Manual - SCRUBTEC 770 / 784 / 795 FORM NO. 70935A - 9 -

71018A

71015A

71017A

WARNING

READ OPERATOR'S

MANUAL BEFORE

OPERATING THIS

MACHINE

RISK OF FIRE

• Use only com-

mercially available

ﬂ oor cleaners and

waxes intended for

machine operation.

• Do not use ﬂ am-

mable materials.

RISK OF INJURY

OR DAMAGE TO

MACHINE

• Do not turn, stop

or leave machine on

a ramp or dock.

WARNING

READ OPERATOR'S

MANUAL BEFORE

OPERATING THIS

MACHINE

EXPLOSIVE GAS-

ES, CAN CAUSE

SEVERE INJURY,

DEATH

OR DAMAGE

TRANSFORMER.

• Keep ﬂ ammable

materials away from

batteries. Charge in

a cool well ventilated

BATTERIES CON-

TAIN SULFURIC

ACID. CAN CAUSE

SEVERE INJURY.

• Avoid contact with

skin eyes, or cloth-

ing. If contact, ﬂ ush

with water. Get

medical attention. If

internal. contact call

physician.

WEAR

PROTECTIVE

EYE GEAR.

71014A

WARNING

MOVING PARTS.

CONTACT CAN

CAUSE SEVERE

INJURY.

• Do not place

hands or feet under

machine when in

use.

WARNING

FALLING PARTS

CAN CAUSE SE-

VERE INJURY.

• Make sure tank

is secure before

servicing.

SYMBOLS USED ON SCRUBTEC 770, 784, 795

Contents

Main Operator's Manual Table of Contents Section II Parts and Service Manual Page Page INTRODUCTION Machine Speci cations Page PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: How To Remove The Machine From A Van Or Truck WARNING: Page SYMBOLS USED ON SCRUBTEC 770, 784, 795 71018A 71015A 71014A 71017A Page Page MACHINE CONTROL PANEL 770L, 784L & 795L Page DISPLAY SCREENS FOR SCRUBTEC 770L, 784L, 795L EN MACHINE CONTROLS & FEATURES CAUTION! HOW TO PREPARE THE MACHINE FOR OPERA- TION HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers BA Page Page Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and recovery tank before doing any maintenance. Keep all fasteners tight. BA Page Page Page HOW TO CORRECT PROBLEMS IN THE MACHINE SCRUBTEC 770L / 784L / 795L WB Common Error Codes Page Parts and Service Manual Page Nil sk ALTO NOTE 1: Only used on the following models: 05210G, 05220G. Solution Tank Assembly 12/09 Item Ref. No. Qty Description Page Nil sk ALTO Recovery Tank Assembly 12/09 Item Ref. No. Qty Description Page Page Page SCRUBTEC 770L / 784L / 795L Control Panel Assembly 12/09 Item Ref. No. Qty Description Nil sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / Solo Speed Controller 12/09 Item Ref. No. Qty Description Page Item Ref. No. Qty Description Nil sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / I-Drive Speed Controller 12/09 Page Squeegee Swing Arm Assembly 12/09 Item Ref. No. Qty Description Page SCRUBTEC 770 / 784 Squeegee Assembly 12/09 Item Ref. No. Qty Description Page Item Ref. No. Qty Description SCRUBTEC 795 Squeegee Assembly 12/09 Nil sk ALTO Traverse System Assembly 2/05 Nil sk ALTO Traverse System Assembly 2/05 Item Ref. No. Qty Description Nil sk ALTO Brush Head Assembly Drawing 2/05 Nil sk ALTO Brush Head Assembly Parts List 11/07 Item Ref. No. Qty Description Item Ref. No. Qty Description Nil sk ALTO Brush Motor #45036A 2/05 Item Ref. No. Qty Description Page Nil sk ALTO Imperial Transaxle Parts 2/05 PN 59116A Item Ref. No. Qty Description Nil sk ALTO Imperial Transaxle Parts 2/05 PN 59116A ACCESSORIES BRUSHES: PAD DRIVERS: Page Page Page Page Page Page Nil sk ALTO reserves the right to make changes or improvements to its machine without notice. Always use genuine Nil sk ALTO Parts for repair. Nil sk ALTO LIMITED U.S. WARRANTY 3 YEARS FOR PARTS AND 1 YEAR FOR SERVICE LABOR (See exceptions below) BATTERY WARRANTY Nil sk ALTO: POLYDUR AUTOMATIC SCRUBBER SOLUTION AND RECOVERY TANK EIGHT-YEAR U.S. GUARANTEE