Nilfisk-ALTO 05210F, 05210G, 05211F, 05220F, 05220G, 05221F, 05230F, 05231F , SCRUBTEC 770 / 784 Squeegee Assembly 12/09 Item Ref. No. Qty Description

Nilﬁ sk ALTO Operator's Manual - SCRUBTEC 770 / 784 / 795 FORM NO. 70935A - 49 -

Nilﬁ sk ALTO

SCRUBTEC 770 / 784Squeegee Assembly 12/09 Item Ref. No. Qty Description

10803KL Squeegee Asm.

1 25201B 2 Knob

2 34260B 1 Squeegee Gasket

3 81301A 2 Nut, 3/8-16 Jam SS

4 30048A 2 Wheel, Gide 4” Diam.

5 53185A 2 Ring, 3/8 ID Snap

6 60272B 1 Channel, Sq. Weldment

7 30058A 1 Spacer, Squeegee

8 30069L 1 Blade, Rear Linatex (STD)

[ ] 30557A 1 Blade-Rear Gum Rubber (OPT)

9 80280A 2 Nut, Squeegee,Backup

10 80011A 2 Screw, 3/8-16 x 3

11 60252A 1 Strap, Clamp Sq. Ret.

12 930086 2 Rivet, 3/16 x .450 Alum.

13 50835A 1 Latch, Sq. Clamp

14 30717L1 1 Blade, Front Linatex (STD)

[ ] 30091A 1 Blade-Front Urethane (OPT)

15 60254A 2 Bolt, Shoulder 5/16 x 2 ¼

16 30049B 4 Wheel, Squeegee

17 81104A 2 Nut, ¼ -20

18 60243A 2 Bracket, Sq. Wheel

19 60358A 2 Shim, Squeegee Wheel

20 980657 4 Washer, ¼ Lock

21 962720 4 Screw, ¼ -20 x ½ Hex

NOTE: When changing squeegee blades, it might be necessary to loosen screw #10; install and secure blades with clamp #13; then retighten screw

#10. This will allow for different thickness.

Contents

Main Operator's Manual Table of Contents Section II Parts and Service Manual Page Page INTRODUCTION Machine Speci cations Page PROCEDURES FOR TRANSPORTING How To Put The Machine In A Van Or Truck WARNING: How To Remove The Machine From A Van Or Truck WARNING: Page SYMBOLS USED ON SCRUBTEC 770, 784, 795 71018A 71015A 71014A 71017A Page Page MACHINE CONTROL PANEL 770L, 784L & 795L Page DISPLAY SCREENS FOR SCRUBTEC 770L, 784L, 795L EN MACHINE CONTROLS & FEATURES CAUTION! HOW TO PREPARE THE MACHINE FOR OPERA- TION HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Brushes Or Pad Drivers BA Page Page Maintenance and repairs must be done by authorized personnel only. Always empty the solution tank and recovery tank before doing any maintenance. Keep all fasteners tight. BA Page Page Page HOW TO CORRECT PROBLEMS IN THE MACHINE SCRUBTEC 770L / 784L / 795L WB Common Error Codes Page Parts and Service Manual Page Nil sk ALTO NOTE 1: Only used on the following models: 05210G, 05220G. Solution Tank Assembly 12/09 Item Ref. No. Qty Description Page Nil sk ALTO Recovery Tank Assembly 12/09 Item Ref. No. Qty Description Page Page Page SCRUBTEC 770L / 784L / 795L Control Panel Assembly 12/09 Item Ref. No. Qty Description Nil sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / Solo Speed Controller 12/09 Item Ref. No. Qty Description Page Item Ref. No. Qty Description Nil sk ALTO SCRUBTEC 770S / 784S / 795S Control Panel Assembly / I-Drive Speed Controller 12/09 Page Squeegee Swing Arm Assembly 12/09 Item Ref. No. Qty Description Page SCRUBTEC 770 / 784 Squeegee Assembly 12/09 Item Ref. No. Qty Description Page Item Ref. No. Qty Description SCRUBTEC 795 Squeegee Assembly 12/09 Nil sk ALTO Traverse System Assembly 2/05 Nil sk ALTO Traverse System Assembly 2/05 Item Ref. No. Qty Description Nil sk ALTO Brush Head Assembly Drawing 2/05 Nil sk ALTO Brush Head Assembly Parts List 11/07 Item Ref. No. Qty Description Item Ref. No. Qty Description Nil sk ALTO Brush Motor #45036A 2/05 Item Ref. No. Qty Description Page Nil sk ALTO Imperial Transaxle Parts 2/05 PN 59116A Item Ref. No. Qty Description Nil sk ALTO Imperial Transaxle Parts 2/05 PN 59116A ACCESSORIES BRUSHES: PAD DRIVERS: Page Page Page Page Page Page Nil sk ALTO reserves the right to make changes or improvements to its machine without notice. Always use genuine Nil sk ALTO Parts for repair. Nil sk ALTO LIMITED U.S. WARRANTY 3 YEARS FOR PARTS AND 1 YEAR FOR SERVICE LABOR (See exceptions below) BATTERY WARRANTY Nil sk ALTO: POLYDUR AUTOMATIC SCRUBBER SOLUTION AND RECOVERY TANK EIGHT-YEAR U.S. GUARANTEE