Manuals / Nlynx / Computer Equipment / Switch

Nlynx Wireless Gateway manual Information - Connections

Models: Wireless Gateway

1 72

Download 72 pages 38.35 Kb

Page 59

Information — Connections

Information — Connections

The Connections information panel gives details of connections between the LAN and the Internet. The source and destination IP addresses identify the machines at the two ends of the connection; the protocol identifies the application being used; and the “Idle (minutes)” column shows how long it has been since the last packet was transferred.

59

Image 59

Nlynx Wireless Gateway manual Information - Connections

Contents

Rev. 01 Oct Wireless GatewayUsers Guide CE Mark Warning FCC WarningBasic Setup Table of ContentsFeatures 3. Web ConfigurationInstallation 4. AppendixReset Factory ResetIntroduction Features∙ LAN-to-WAN access control on basis of IP or MAC address or both ∙ Configurable as a DHCP Dynamic Host Configuration Protocol server∙ Configurable for NAT or router mode ∙ Configurable for dynamic routing on LAN and/or WANBack Panel External ComponentsFront Panel Component FaultyLPT LED Web Configuration Note If the operating system or the browser is set to use an HTTP proxy server, either turn off the setting or put theWireless Gateways IP address in the list of unproxied hosts 4. Command the browser to access the following URL∙ Broadband Router ∙ Wireless AP ∙ Print Server ∙ Admin Password Basic SetupLocal LAN Basic Setup - Broadband RouterRouter Name Global WAN Mode DNS IP Addresses WAN Port MAC Save/CancelESS-ID Basic Setup - Wireless APWireless Channel Save/Cancel Tx Bit RateIf the Wireless Gateway is the only AP on your LAN, it does not matter which channel you set the unit to use properly configured 802.11b wireless stations will find the correct channel automatically AppleTalk Basic Setup - Print ServerPrint Port TCP/IPSave/Cancel Machines running the Macintosh OS on your LAN can print on a PostScript printer attached to the Wireless Gateway. When such machines request information about network printers using the AppleTalk protocol, the Wireless Gateway will respond with the information shown in the Print Server panel. This information must be correct for successful printingBasic Setup - Admin Password Advanced Settings Advanced Settings - DHCP Server Address Range EnableReserve Table Lease Timetwelve hexadecimal digits with or without spaces in between. The hexadecimal digits are 0 through 9 and A through F in upper or lower case 0080C82F8086, 0080c82f8086, 0080C8 2F8086, and 00 80 C8 2F 80 86 are all different ways of writing the same MAC address Save/CancelAdvanced Settings - Port Forwarding TCP Port to IP Forwarding Save/Cancel DMZ HostA DMZ host is a machine exposed to the Internet and running software designed to provide specific services while protecting the LANs other machines from direct access from outside. On the Wireless Gateway, if an IP address for a DMZ host is specified, incoming packets of types not listed in the TCP Port to IP Forwarding table will be directed to the DMZ host Enable Advanced Settings - Port OpenGo to ApplicationDefine Port Open List to specify a range, click the range, and then click in the Static Routing Advanced Settings - RoutingDynamic Routing Save/Cancel NAT/Router ModeThe LAN Interface settings control whether and how the Wireless Gateway uses RIP with any routing devices networked to it through its LAN ports Page Advanced Settings - Filters Protocols Filter Users FilterThe Protocols Filter control lets you list the TCP port numbers for up to sixteen protocols that you do not want LAN users to use over the WAN connection. A list of standard, commonly used TCP port numbers appears next to the table to help you create entries. To create an entry, simply click in a TCP Port # box and type a port number NetBIOS over TCP/IP FilterBlock WAN Request Save/CancelPage Advanced Settings - Manager Console Log and Filter Manager ConsoleSchedule Connection Save/Cancel ∙ Manual Connect means to connect only on command from the managerDefine User List Advanced Settings - Wireless AccessAccess Control Enable/Disable Advanced Settings - Wireless EncryptionKey 1 through Key Encrypt Data Transmissions UsingInput Format Save/Cancel This control determines which key the Wireless Gateway will use when WEP encryption is enabled. Click the list box to open it, and then drag to or click the name of the desired keyAdvanced Settings - Wireless Bridge Broadcast/Multicast Filter Protocol FiltersPage or 00 80 C8 2F 80 86. To list a station, find its MAC address, click in a MAC Address box, and type the address, with or without spaces Save/CancelInformation Information - Device Information - DHCP Information - Routing Information - Users Information - Connections Information - WAN Link Information - Printer Status Information - Wireless Stations Information - Wireless Tallies Page Tools Tools - ResetTools - PPPoE Connect and PPPoE Disconnect Tools - Factory ResetTools - Print Test Page and the version of the Wireless Gateway HelpDevice Utility InstallationAppendix Using Device Utility Changing IP Address Firmware UpgradeNetwork Protocols Supported Operating Temperature 0 to 50C Storage Temperature -25 to 55CSpecifications External Connection