Manuals / Nlynx / Computer Equipment / Switch

Nlynx Wireless Gateway manual

Models: Wireless Gateway

1 72

Download 72 pages 38.35 Kb

Page 40

After making sure all settings in the Filters settings panel are correct, click Save to store the settings in the Wireless Gateway's non-volatile memory. You can, alternatively, click Cancel (or simply exit the panel) to restore all settings in the panel to the values last saved to or retrieved from the Wireless Gateway.

40

Image 40

Nlynx Wireless Gateway manual

Contents

Users Guide Wireless GatewayRev. 01 Oct FCC Warning CE Mark WarningTable of Contents Features3. Web Configuration Basic Setup4. Appendix ResetFactory Reset InstallationFeatures Introduction∙ Configurable as a DHCP Dynamic Host Configuration Protocol server ∙ Configurable for NAT or router mode∙ Configurable for dynamic routing on LAN and/or WAN ∙ LAN-to-WAN access control on basis of IP or MAC address or bothExternal Components Back PanelFront Panel LPT LED FaultyComponent Web Configuration HTTP proxy server, either turn off the setting or put the Wireless Gateways IP address in the list of unproxied hosts4. Command the browser to access the following URL Note If the operating system or the browser is set to use anBasic Setup ∙ Broadband Router ∙ Wireless AP ∙ Print Server ∙ Admin PasswordRouter Name Basic Setup - Broadband RouterLocal LAN Global WAN Mode DNS IP Addresses Save/Cancel WAN Port MACWireless Channel Basic Setup - Wireless APESS-ID If the Wireless Gateway is the only AP on your LAN, it does not matter which channel you set the unit to use properly configured 802.11b wireless stations will find the correct channel automatically Tx Bit RateSave/Cancel Basic Setup - Print Server Print PortTCP/IP AppleTalkMachines running the Macintosh OS on your LAN can print on a PostScript printer attached to the Wireless Gateway. When such machines request information about network printers using the AppleTalk protocol, the Wireless Gateway will respond with the information shown in the Print Server panel. This information must be correct for successful printing Save/CancelBasic Setup - Admin Password Advanced Settings Advanced Settings - DHCP Server Enable Address RangeLease Time Reserve TableSave/Cancel twelve hexadecimal digits with or without spaces in between. The hexadecimal digits are 0 through 9 and A through F in upper or lower case 0080C82F8086, 0080c82f8086, 0080C8 2F8086, and 00 80 C8 2F 80 86 are all different ways of writing the same MAC addressAdvanced Settings - Port Forwarding TCP Port to IP Forwarding A DMZ host is a machine exposed to the Internet and running software designed to provide specific services while protecting the LANs other machines from direct access from outside. On the Wireless Gateway, if an IP address for a DMZ host is specified, incoming packets of types not listed in the TCP Port to IP Forwarding table will be directed to the DMZ host DMZ HostSave/Cancel Advanced Settings - Port Open Go toApplication EnableDefine Port Open List to specify a range, click the range, and then click in the Advanced Settings - Routing Static RoutingDynamic Routing The LAN Interface settings control whether and how the Wireless Gateway uses RIP with any routing devices networked to it through its LAN ports NAT/Router ModeSave/Cancel Page Advanced Settings - Filters Users Filter Protocols FilterNetBIOS over TCP/IP Filter Block WAN RequestSave/Cancel The Protocols Filter control lets you list the TCP port numbers for up to sixteen protocols that you do not want LAN users to use over the WAN connection. A list of standard, commonly used TCP port numbers appears next to the table to help you create entries. To create an entry, simply click in a TCP Port # box and type a port numberPage Advanced Settings - Manager Console Manager Console Log and FilterSchedule Connection ∙ Manual Connect means to connect only on command from the manager Save/CancelAdvanced Settings - Wireless Access Define User ListAccess Control Advanced Settings - Wireless Encryption Enable/DisableInput Format Encrypt Data Transmissions UsingKey 1 through Key This control determines which key the Wireless Gateway will use when WEP encryption is enabled. Click the list box to open it, and then drag to or click the name of the desired key Save/CancelAdvanced Settings - Wireless Bridge Protocol Filters Broadcast/Multicast FilterPage Save/Cancel or 00 80 C8 2F 80 86. To list a station, find its MAC address, click in a MAC Address box, and type the address, with or without spacesInformation Information - Device Information - DHCP Information - Routing Information - Users Information - Connections Information - WAN Link Information - Printer Status Information - Wireless Stations Information - Wireless Tallies Page Tools - Reset ToolsTools - Print Test Tools - Factory ResetTools - PPPoE Connect and PPPoE Disconnect Page Help and the version of the Wireless GatewayAppendix InstallationDevice Utility Using Device Utility Firmware Upgrade Changing IP AddressOperating Temperature 0 to 50C Storage Temperature -25 to 55C SpecificationsExternal Connection Network Protocols Supported