Manuals / Nlynx / Computer Equipment / Switch

Nlynx Wireless Gateway manual Advanced Settings - Routing, Static Routing

Models: Wireless Gateway

1 72

Page 33

Advanced Settings — Routing

Routing settings determine whether the Wireless Gateway acts as a router, and how it interacts with other routers for efficient dispatching of packets to other networks.

To view the Routing settings panel, click Routing in the command panel at the left edge of your browser window (if the command does not appear there, click Advanced Settings at the top of the window first). The Routing settings panel will appear. The controls in this panel are explained below.

Static Routing

Page 33

Image 33

Nlynx Wireless Gateway manual Advanced Settings - Routing, Static Routing

Contents

Wireless Gateway Users GuideRev. 01 Oct CE Mark Warning FCC WarningFeatures Table of Contents3. Web Configuration Basic SetupReset 4. AppendixFactory Reset InstallationIntroduction Features∙ Configurable for NAT or router mode ∙ Configurable as a DHCP Dynamic Host Configuration Protocol server∙ Configurable for dynamic routing on LAN and/or WAN ∙ LAN-to-WAN access control on basis of IP or MAC address or bothBack Panel External ComponentsFront Panel Faulty LPT LEDComponent Web Configuration Wireless Gateways IP address in the list of unproxied hosts HTTP proxy server, either turn off the setting or put the4. Command the browser to access the following URL Note If the operating system or the browser is set to use an∙ Broadband Router ∙ Wireless AP ∙ Print Server ∙ Admin Password Basic SetupBasic Setup - Broadband Router Router NameLocal LAN Global WAN Mode DNS IP Addresses WAN Port MAC Save/CancelBasic Setup - Wireless AP Wireless ChannelESS-ID Tx Bit Rate If the Wireless Gateway is the only AP on your LAN, it does not matter which channel you set the unit to use properly configured 802.11b wireless stations will find the correct channel automaticallySave/Cancel Print Port Basic Setup - Print ServerTCP/IP AppleTalkSave/Cancel Machines running the Macintosh OS on your LAN can print on a PostScript printer attached to the Wireless Gateway. When such machines request information about network printers using the AppleTalk protocol, the Wireless Gateway will respond with the information shown in the Print Server panel. This information must be correct for successful printingBasic Setup - Admin Password Advanced Settings Advanced Settings - DHCP Server Address Range EnableReserve Table Lease Timetwelve hexadecimal digits with or without spaces in between. The hexadecimal digits are 0 through 9 and A through F in upper or lower case 0080C82F8086, 0080c82f8086, 0080C8 2F8086, and 00 80 C8 2F 80 86 are all different ways of writing the same MAC address Save/CancelAdvanced Settings - Port Forwarding TCP Port to IP Forwarding DMZ Host A DMZ host is a machine exposed to the Internet and running software designed to provide specific services while protecting the LANs other machines from direct access from outside. On the Wireless Gateway, if an IP address for a DMZ host is specified, incoming packets of types not listed in the TCP Port to IP Forwarding table will be directed to the DMZ hostSave/Cancel Go to Advanced Settings - Port OpenApplication EnableDefine Port Open List to specify a range, click the range, and then click in the Static Routing Advanced Settings - RoutingDynamic Routing NAT/Router Mode The LAN Interface settings control whether and how the Wireless Gateway uses RIP with any routing devices networked to it through its LAN portsSave/Cancel Page Advanced Settings - Filters Protocols Filter Users FilterBlock WAN Request NetBIOS over TCP/IP FilterSave/Cancel The Protocols Filter control lets you list the TCP port numbers for up to sixteen protocols that you do not want LAN users to use over the WAN connection. A list of standard, commonly used TCP port numbers appears next to the table to help you create entries. To create an entry, simply click in a TCP Port # box and type a port numberPage Advanced Settings - Manager Console Log and Filter Manager ConsoleSchedule Connection Save/Cancel ∙ Manual Connect means to connect only on command from the managerDefine User List Advanced Settings - Wireless AccessAccess Control Enable/Disable Advanced Settings - Wireless EncryptionEncrypt Data Transmissions Using Input FormatKey 1 through Key Save/Cancel This control determines which key the Wireless Gateway will use when WEP encryption is enabled. Click the list box to open it, and then drag to or click the name of the desired keyAdvanced Settings - Wireless Bridge Broadcast/Multicast Filter Protocol FiltersPage or 00 80 C8 2F 80 86. To list a station, find its MAC address, click in a MAC Address box, and type the address, with or without spaces Save/CancelInformation Information - Device Information - DHCP Information - Routing Information - Users Information - Connections Information - WAN Link Information - Printer Status Information - Wireless Stations Information - Wireless Tallies Page Tools Tools - ResetTools - Factory Reset Tools - Print TestTools - PPPoE Connect and PPPoE Disconnect Page and the version of the Wireless Gateway HelpInstallation AppendixDevice Utility Using Device Utility Changing IP Address Firmware UpgradeSpecifications Operating Temperature 0 to 50C Storage Temperature -25 to 55CExternal Connection Network Protocols Supported