HOW TO USE THE CHEST PULSE SENSOR
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com CDs and videos are played
HOW TO PUT ON THE CHEST PULSE SENSOR
The chest pulse sensor consists of two components: the chest strap and the sensor unit (see the drawing below). Insert the tab on one end of the chest strap into one end of the sensor unit, as shown in the inset draw- ing. Press the end of the sensor unit under the buckle on the chest strap. The tab should be flush with the front of the sensor unit.
| Chest Strap |
| |
Tabs |
|
| |
| Tab | ||
Sensor Unit | Sensor | Buckle | |
Unit | |||
|
| ||
Next, wrap the chest pulse sen- sor around your chest, and attach the other end of the chest strap to the sensor unit. Adjust the length of the chest strap,
if necessary. The chest pulse sen-
sor should be under your clothes, tight against your skin, and as high under the pectoral muscles or breasts as is comfortable. Make sure that the logo on the sensor unit is facing forward and is
Pull the sensor unit away from your body a few inches and locate the two electrode areas on the inner side (the electrode areas are covered by shallow ridges). Using saline solution such as saliva or contact lens so- lution, wet both electrode areas. Return the sensor unit to a position against your chest.
CHEST PULSE SENSOR CARE AND MAINTENANCE
•Thoroughly dry the chest pulse sensor after each use. The chest pulse sensor is activated when the electrode areas are wetted and the heart rate monitor is put on; the chest pulse sensor shuts off when it is removed and the electrode areas are
dried. If the chest pulse sensor is not dried after each use, it may remain activated longer than nec- essary, draining the battery prematurely.
•Store the chest pulse sensor in a warm, dry place. Do not store the chest pulse sensor in a plastic bag or other container that may trap moisture.
•Do not expose the chest pulse sensor to direct sunlight for extended periods of time; do not expose it to temperatures above 50° Celsius (122° Fahrenheit) or below
•Do not excessively bend or stretch the sensor unit when using or storing the chest pulse sensor.
•Clean the sensor unit using a damp
CHEST PULSE SENSOR TROUBLESHOOTING
The instructions on the following pages explain how the chest pulse sensor is used with the con- sole. If the chest pulse sensor does not function properly, try the steps below.
•Make sure that you are wearing the chest pulse sen- sor as described at the left. Note: If the chest pulse sensor does not function when positioned as de- scribed, move it slightly lower or higher on your chest.
•Use saline solution such as saliva or contact lens solution to wet the two electrode areas on the sensor unit. If heart rate readings do not appear until you begin perspiring,
•As you walk or run on the treadmill, position your- self near the centre of the walking belt. For the console to display heart rate readings, the user must be within arm’s length of the console.
•The chest pulse sensor is designed to work with people who have normal heart rhythms. Heart rate reading problems may be caused by medical conditions such as premature ventricular contrac- tions (pvcs), tachycardia bursts, and arrhythmia.
•The operation of the chest pulse sensor can be affected by magnetic interference caused by high power lines or other sources. If it is suspected that this is a problem, try relocating the treadmill.
•The CR2032 battery may need to be replaced (see page 29).
SOLUTION: a. With the key in the console, press one of the Incline buttons. Whilst the incline is changing, re- move the key. After a few seconds,
PROBLEM: The heart rate monitor does not function properly
SOLUTION: a. If the heart rate monitor does not function properly, see CHEST PULSE SENSOR TROUBLE- SHOOTING on page 8.
b. If the heart rate monitor still does not function properly, the battery |
|
|
|
|
|
|
| b |
|
|
|
| |
should be changed. To replace the battery, locate the battery cover |
|
| Battery Cover |
| ||
|
|
|
| |||
|
|
|
| |||
on the back of the sensor unit. Insert a coin into the slot in the cover |
|
|
|
|
|
|
and turn the cover counterclockwise to the “open” position. Remove |
|
|
|
|
|
|
the cover. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Remove the old battery from the sensor unit. Insert a new CR 2032 |
|
|
|
|
|
|
|
battery, making sure that the writing is on top. In addition, make sure |
|
|
|
| Battery |
| |
that the rubber gasket is in place in the sensor unit. Replace the bat- |
|
|
|
| Cover |
| |
|
|
|
|
|
|
| |
tery cover and turn it to the closed position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| Battery |
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| Rubber | |||
|
|
|
| Gasket |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8 | 29 |
