![](/images/new-backgrounds/1297910/29791013x1.webp)
3. Cut the rubber band holding the Upright Wire Harness | 3 |
|
| 98 |
(98). Have a second person hold the console assembly |
|
| ||
|
|
| ||
|
|
|
| |
near the Uprights (69). Connect the Upright Wire Harness |
|
| 81 |
|
to the wires extending from the Console Base (81). The |
|
|
| |
connectors should slide together easily and snap into |
|
|
|
|
place. If they do not, turn one connector and try again. |
|
|
|
|
Insert the connectors and the Upright Wire Harness into |
| 98 |
|
|
the right Upright, and then set the console assembly on |
|
|
|
|
the Uprights. Be careful not to pinch the wires. |
|
|
|
|
|
|
| 69 |
|
| Console |
|
|
|
| Assembly |
|
|
|
4. Insert a Handrail (118) into the right side of the console | 4 |
|
|
|
assembly as shown; you may need to twist the Handrail |
|
|
| |
|
|
|
| |
as you insert it. Next, insert two 4 1/2” Bolts (78) with |
|
|
|
|
Handrail Bushings (77) into the right Upright (69) and the |
|
|
|
|
Handrail. Be careful not to pinch the wires. Make sure |
|
|
|
|
that the Handrail Bushings are flush against the right |
|
|
|
|
Upright, with the thicker sides facing the center of the |
|
| 69 |
|
treadmill, as shown in the inset drawing. |
|
| Thick | |
|
| 77 | ||
|
|
| ||
Next, lift the console assembly and the Handrail (118) |
|
|
| Side |
118 |
|
|
| |
slightly and align the 4 1/2” Bolts (78) with the holes in the |
|
|
| |
|
|
|
| |
Handrail. Thread the Bolts into the Upright (69) and the |
|
|
|
|
Handrail until the heads of the Bolts are against the |
| 77 | 78 |
|
Upright. Do not tighten the Bolts yet. |
|
| ||
| Console |
|
| |
|
|
|
| |
Attach the other Handrail (not shown) in the same way. |
| Assembly |
|
|
Note: There are no wires on the left side. |
|
|
|
|
5. With the help of a second person, carefully tip the | 5 |
|
|
|
Uprights (69) down to the position shown. Make sure that |
|
|
| |
|
|
| 99 | |
the Extension Legs (102) remain in the Uprights. |
|
|
| |
|
|
|
| |
Attach each Extension Leg (102) with two 1” Tek Screws | 69 |
|
| 53 |
|
|
| ||
(47) and a Base Pad (99) as shown. Note: Attach the |
|
|
|
|
lower Screw (without the Base Pad) first. Next, align the |
|
|
| 99 |
lower ends of the Handrails (118) with the holes in the |
|
|
| |
|
|
| 47 | |
base of the Uprights (69). Attach each Handrail with a 4” |
| 99 |
| |
|
|
| ||
Bolt (53) as shown. Note: The Bolts must be at an |
|
| 102 | 99 |
angle that matches the angle of the Handrails as |
| 53 |
| |
|
|
| ||
shown in the inset drawing. |
|
|
| |
|
|
|
| |
With the help of a second person, carefully tip the | 118 | 99 |
|
|
47 |
|
| ||
Uprights (69) back to the vertical position. See step 4. |
|
| 53 | |
|
|
| ||
Tighten the four 4 1/2” Bolts (78). | 102 |
|
| |
99 |
|
| ||
|
|
|
| |
Note: A replacement Base Pad (99) may be included. Use |
|
| 118 |
|
the Base Pad to replace any Base Pad that becomes worn. |
|
|
|
|
6.Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 26). To protect the floor or carpet from damage, place a mat under the treadmill.
7