7. Route the Upright Wire (28) through one of the | 7 |
|
|
|
|
Handrails (18) as shown, and remove the wire tie |
|
|
|
| |
| 20 |
|
|
| |
from the Upright Wire. |
|
|
|
| |
|
|
|
|
| |
Attach the Handrail (18) to the Right Upright (36) |
| 19 |
| 28 | Wire Tie |
with two 5/16" X 2 1/4" Bolts (20) and two 5/16" |
|
| 31 | 20 |
|
Star Washers (19). Be careful not to pinch the |
|
|
| ||
|
|
|
| ||
Upright Wire (28). |
|
|
|
|
|
Attach the other Handrail (18) to the Left Upright |
| 18 | 18 | 19 |
|
(31) with two 5/16" X 2 1/4" Bolts (20) and two |
|
|
|
| |
5/16" Star Washers (19). |
|
|
|
|
|
|
|
|
| 36 |
|
8. While another person holds the Console Base | 8 |
|
|
|
|
(26) near the right Handrail (18), attach the |
|
| 26 |
| |
|
|
|
| ||
ground wire on the Console Base to the right |
|
|
|
|
|
Handrail with a 1/2" Ground Screw (11). |
|
| 11 | Ground |
|
|
| Wire |
| ||
Connect the wire harness on the Console Base |
|
| Wire |
| |
| Harness |
|
|
| |
(26) to the Upright Wire (28). See the inset |
|
|
|
| |
|
|
|
|
| |
drawing. The connectors should slide to- |
|
| 28 |
|
|
gether easily and snap into place. If they do |
|
|
|
| |
|
|
|
|
| |
not, turn one connector and try again. IF THE |
|
|
| 18 |
|
CONNECTORS ARE NOT CONNECTED PROP- |
|
|
|
| |
|
|
|
|
| |
ERLY, THE CONSOLE MAY BE DAMAGED |
|
|
|
|
|
WHEN THE POWER IS TURNED ON. |
|
|
|
|
|
|
|
|
| 28 |
|
9. Insert the wires into the Console Base (26) as | 9 |
|
|
|
|
you set the Console Base on the Handrails (18). |
|
|
|
| |
| 26 | Front View |
| ||
Be careful not to pinch the wires. Next, thread |
|
| |||
|
|
|
| ||
two 1/4" X 1/2" Bolts (22) with 1/4" Star Washers |
|
|
|
|
|
(21) into the Handrails and the Console Base; do | 18 |
|
|
| 18 |
not tighten the Bolts yet. |
|
|
|
| |
|
|
|
|
| |
Attach the Console Base (26) to the Handrails |
|
|
|
|
|
(18) with four 3/4" Screws (2). Then, tighten the |
|
|
|
|
|
two 1/4" X 1/2" Bolts (22). |
|
|
|
|
|
|
| 21 |
| 2 |
|
| 2 |
|
|
| |
| 22 |
| 21 | ||
|
|
|
| ||
|
|
|
|
| 22 |
| 9 |
|
|
|
|
